Open the lower side cover, Remove the misfed paper

TROUBLESHOOTING

MISFEED IN THE LOWER PAPER TRAY (Two-tray model only)

Note	Make sure that there is no misfed paper in the tray before pulling it out. (p.49)

1 Open the lower side cover.

Grasp the handle to open the lower side cover.

2 Remove the misfed paper.

Be careful not to tear the misfed paper during removal.

3 If the misfed paper is not seen in step 2, lift and pull out the lower paper tray and remove the misfed paper.

Be careful not to tear the misfed paper during removal.

4 Close the lower side cover.

The misfeed indicator () will go out.

5 Close the lower paper tray.

If the misfeed indicator ( ) does not stop

Note	blinking, check for torn pieces of paper in the
	blinking, check for torn pieces of paper in the
	machine.

Page 57

Image 57

Olivetti 20W Open the lower side cover, Remove the misfed paper, Close the lower side cover, Close the lower paper tray

Contents

Copia 16W Copia 20W Copia 16W d-Copia 20W Publication Issued by Page For Countries in the European Union EU Contents Troubleshooting Do not install your machine in areas that are Important Points When Selecting AN Installation Site Trademark acknowledgements Environmental Information Software Setup Guide separate manual Online Manual on the accessory CD-ROMMeaning of R in Original and Paper Size Indications Conventions Used in this Manual AB series metric and inch series references Differences Between Models High-speed laser copying Enhanced copying featuresHigh-quality digital image Scan once/Print many Contains operation keys and indicator lights. p.10 Press to turn the machine power on and off. p.12Adjust to the width of the paper. p.15 Use to clean the transfer charger. p.57 Open to remove misfed originals. p.47 Adjust to the size of the originalsOriginals exit the machine here after copying Contains toner. p.54 Operation Panel Use to set the paper size in the paper trays. p.16 Light up to show the selected copy paper size. p.16Use to manually select a paper tray. p.21 Press for automatic copy ratio selection. p.22 Power OFF Power onPower Save Modes Initial settings Paper Follow these guidelines when using special papersSpecial papers For best results, use only Olivetti recommended paper Loading the paper tray Loading PaperPush the centre Pressure plate down until It locks into place Loading the bypass tray Important points when inserting paper in the bypass tray Envelopes Changing a TRAY’S Paper Size Setting Press the Start key and then the Paper Size Enter key Normal Copying Copying from the document glassOpen the document cover/SPF, and place the original Set the originals face up in the document feeder tray Copying from the SPF Auto paper select mode Two-tray model only Making a Copy Darker or Lighter Auto tray switching Two-tray model onlySelecting the Tray Original types REDUCTION/ENLARGEMENT/ZOOM Setting the Number of CopiesAutomatic Ratio Selection Original position Selectable ratios Fine adjustment of the ratio Selecting a preset ratioManual Ratio Selection Press the Auto Image key Auto % Press the Copy ratio display key XY Zoom copying Press the Copy ratio display key TWO-SIDED Copying Using the Bypass Tray Copy original aPlace original B as shown below Dual page Copying Copy indicator Is litSet the original size to A3 11 x Press the Dual page Copy key Interrupting a Copy RUN Press the Interrupt key to interrupt the copy runReplace the previous originals and press the Start key Basic Procedure for Printing Using the Printer ModeMaketray. sure that paper is loaded Click the Print button or the OK button to begin printing When Use close paper size is disabled Pausing a print jobWhen Use close paper size is enabled Operation in Copy and Printer Modes Adjusting the Automatic Exposure Level SettingTo complete When enabling toner Toner Save Mode and High Image Quality ModePhoto indicator stops blinking and lights steadily Save mode, make sure User Programs Customising Settings Minimum 300 dpiShort beep Copies Base settings Selecting a Setting for a User Program Settings for Auditing Mode Auditing ModeAuditing Mode Settings For the setting codes, see Auditing Mode SETTINGS. p.36 Selecting Auditing Mode Settings Account number entry Auditing modeAccount number change Account number deletion Copying when Auditing mode is enabled Resetting account Troubleshooting MACHINE/COPYING Problems Paper is not loaded properly Problem Cause and solution Misfeed occursPieces of paper inside machine Paper misfeed Too much paper is loaded in the tray Original smudged or blotchy Any other indicators are litCopies Transfer charger is dirty Copying or printing is performed Printing Problems Removing the software Click the start button, and then click Control PanelClick Add or Remove Programs Indicators and Display Messages Misfeed in the SPF Misfeed RemovalRemove the misfed original Copia 20W Copia 16W Misfeed in the Bypass Tray Misfeed indicator will go out Misfeed in the paper feed area Misfeed in the Machine Lower the fusing unit release levers to Misfeed in the fusing areaAllow easier removal Misfed paper during Close the side cover Misfeed in the transport areaBe careful not to tear the misfed paper during removal Be careful not to tear Misfed paper during Removal Misfeed in the Upper Paper Tray Close the upper paper trayPush the upper paper tray in completely Remove the misfed paper Open the lower side coverClose the lower side cover Close the lower paper tray Replacing the Toner Cartridge Toner cartridge replacement required indicator will go outClose the front cover Green part of the cartridge Checking the Total Output Count Checking the Total Output Count and Toner LevelTotal output count Total copy count Cleaning the Document Glass and SPF/ Document Cover Routine MaintenanceChecking the Toner Level Press the Light key to return to the normal display Cleaning the Transfer Charger Cleaning the Bypass Tray Paper Feed Roller Specifications Peripheral DevicesSingle Pass Feeder Proper Storage Storage of SuppliesStore the supplies in a location that is Store paper in the wrapper and lying flat Specifications Printer Function Software License Page Index Symbols Troubleshooting Preset Ratio selector indicatorOriginal types 10, 13 Machine settings Problem occursIndicators, lit and blinking Page Class Laser Product Laser Klasse Page Code

Olivetti 20W, 16W Open the lower side cover, Remove the misfed paper, Close the lower side cover

Models: 20W 16W

MISFEED IN THE LOWER PAPER TRAY (Two-tray model only)

1 Open the lower side cover.

Grasp the handle to open the lower side cover.

2 Remove the misfed paper.

Be careful not to tear the misfed paper during removal.

Be careful not to tear the misfed paper during removal.

4 Close the lower side cover.

The misfeed indicator () will go out.

5 Close the lower paper tray.