Onkyo DR-S2.2 instruction manual Setting the TV System Other than North American model

Connecting the Power/ Turning on the DVD Receiver

Before connecting

•Make sure that all the connections from pages 15 to 25 are complete (the connection to the TV is required).

•Turning on the DVD Receiver may cause a momentary power surge, which might interfere with other electrical equipment such as computers. If this happens, use a wall outlet on a different circuit.

(European and some Asian models)

•The DVD Receiver is shipped with the main power (POWER) switch in the on position (_ ON). When the power cord is plugged in for the first time, the DVD Receiver will automatically enter the standby state (same condition after step 2 below).

POWER (European and some Asian models only) STANDBY indicator

STANDBY/ON

Display	Front panel
	illumination

1	Connect the power cord to a wall
	outlet.
	(Other than European and some Asian
	models)
	The DVD Receiver enters the standby
	mode and the STANDBY indicator lights
	up.
2	(European and some Asian models
	only)

Press POWER to switch on the main power to put the DVD Receiver in the standby mode.

The STANDBY indicator lights up.

•The buttons on the remote controller do not operate if the POWER switch is set to OFF.

•To switch off the main power, press POWER again.

3	Press STANDBY/ON on the DVD
	Receiver or ON on the remote

controller to turn on the DVD Receiver.

The light and display on the DVD Receiver’s front panel light. At the same time, the STANDBY indicator goes off.

•To put the DVD Receiver in the standby mode, press STANDBY/ON on the DVD Receiver, or STANDBY on the remote controller. Be sure to set the volume to minimum before putting the DVD Receiver in the standby mode for the next use to avoid sudden loud sound reproduction.

•While in the STANDBY mode, the DVD Receiver can receive signals from the remote controller. However, if you press POWER on the DVD Receiver to switch off the main power, the remote controller cannot be used to turn on the DVD Receiver.

•Setting the STANDBY button to standby does not shut off the power completely.

■Setting the TV System (Other than North American model)

The default setting of the DVD Receiver is AUTO, and unless you notice that the picture is distorted when playing some discs, you should leave it set to AUTO.

If you experience picture distortion with some discs, set the TV system to match your country or region’s system. Doing this, however, may restrict the kinds of disc you can watch. The table below shows what kinds of disc are compatible with each setting (AUTO, PAL and NTSC).

Disc				Output format
Type	Format		Position of TV SYSTEM mode
		NTSC		PAL	AUTO
DVD	NTSC	NTSC		MOD. PAL	NTSC
	PAL			PAL	PAL
Video CD	NTSC	NTSC		MOD. PAL	NTSC
	PAL	NTSC		PAL	PAL
CD, No disc		NTSC		PAL	NTSC or PAL

1Switch the DVD Receiver into standby.

2Hold down ¢ then press STANDBY/ON until the display indicates the new setting to switch the TV system.

The TV system changes as follows:

AUTO =	NTSC
NTSC =	PAL
PAL =	AUTO

Note that you have to switch the player into standby before each change.

About MOD. (Modulation) PAL

•SHRINK

Most models of the newly developed countdown PAL TV system detect 50 Hz (PAL)/60 Hz (NTSC) and automatically switch vertical amplitude, resulting in a display without vertical shrinkage.

•If your PAL TV does not have a V-Hold control, you may not be able to view NTSC disc because the picture may roll. If the TV has a V-Hold control, adjust it until the picture stops rolling. On some TVs, the picture may shrink vertically, leaving black bands at the top and bottom of the screen. This is not a malfunction; it is caused by the NTSC = PAL conversion.

26