Rear panel facilities

(RI)

The terminal on the TX-DS898 is for connecting other Onkyo

components equipped with the same terminal. When a

component is -connected, you can point the remote controller supplied with the TX-DS898 at the sensor on the TX-DS898 and operate that component without having to switch remote controllers.

In addition, by connecting components to the terminal, you can also perform the system operations given below.

Power on/ready function

When the TX-DS898 is in the standby state, if an -connected component is turned on, then the TX-DS898 also turns on and the input source selected at the TX-DS898 automatically switches to that component.

If the power cord for an -connected component is connected to the AC OUTLET on the TX-DS898, or if the TX-DS898 is turned on, this function will not work.

Direct change function

When the play button is pressed at an -connected component, the input source selected at the TX-DS898 automatically changes to that component.

Power off function

When the TX-DS898 is placed in the standby state, all - connected components are also automatically put into the standby state.

CAUTION

If an MD recorder is connected to the TAPE jack on the TX-DS898, switch the Input Selector from TAPE to MD (see page 25).

TX-DS898

connector

Ex: Onkyo CD player

connector

Ex: Onkyo cassette tape deck

IR IN/OUT

If the TX-DS898 is located inside a rack or cabinet that will not allow infrared beams to reach the IR sensor, you will need to connect a remote sensor to IR IN input to be able to use the remote controller. Then install the remote sensor in an unblocked location where you can easily point the remote controller.

Using a mini-jack connector, connect the IR emitter to the IR OUT terminal on the TX-DS898 and then place the IR emitter on the remote sensor of the component or facing it.

VIDEO IN/OUT

These are the video inputs and outputs. On the rear panel, there are five video inputs and two video outputs and each one includes both composite video and S video configurations. Connect VCRs, LD players, DVD players, and other video components to the video inputs.

The two video output channels can be used to be connected to video tape recorders for making recordings.

When connecting a VCR or other video component, make sure you connect the audio and video leads together (i.e., both to VIDEO 3).

The VIDEO 5 inputs are located on the front panel.

Composite video jack

S video jack

MULTI CHANNEL INPUT

By connecting a DVD player, MPEG decoder, or other component that has a multi channel port, you can playback the audio with 5.1 channel or 7.1 channel output. So, be sure to prepare a cable that can properly connect the TX-DS898 to the peripheral device.

L (white)

Front output

R (red)

DIGITAL

PRE OUT

OUTPUT

R

L

 

OPT

FRONT

 

To connect components using the terminal, simply connect a

remote control cable from this terminal to the terminal of the

other component. An remote control cable with a 1/8-inch (3.5-

mm)miniature two-conductor plug comes with every cassette tape deck, compact disc player, MD recorder, and DVD player that has an terminal.

Subwoofer

L (white)

Surround

R (red)

Ex: DVD-Audio player/

MPEG decoder

1

 

SUB

2

 

COAX

SURR

1

 

 

SURR

 

BACK/

2

ZONE 2

 

3

FRONT

 

OPT

SUB

1

 

SURR

2

CENTER

MULTI C INPUT

CENTER

When performing operations with -connected components

using the system, do not use the remote zone (Zone 2).

For remote control operation, the audio connection cables must also be connected.

If a component has two terminals, you can use either one to connect to the TX-DS898. The other one can be used to daisy chain with another component.

With Onkyo DVD players, you can enter the pre-program code so that you can operate the DVD player directly with the remote

controller without connecting the terminals (see page 59).

 

SURR

 

 

BACK

 

 

3

 

 

R

L

 

R (red)

 

Surround back

4

 

GND

 

 

DIGITAL

 

 

INPUT

 

 

L (white)

 

Center

 

 

GND

Use this GND terminal for connecting the ground (or earth) wire if a turntable is connected. Refer to “Connecting a turntable” on page 15.

14

Page 14
Image 14
Onkyo TX-DS898 instruction manual Ir In/Out, Video IN/OUT, Multi Channel Input, Gnd