$ Search control commands
| Data transmitted by PC | Data returned from unit in response |
| Description of command | |||
|
|
|
|
|
| ||
|
|
|
|
|
| ||
| [STX] SAS:data [ETX] | [STX] SAS [ETX] | Searches the alarm number designated by the parameter in | ||||
Parameter |
|
|
| the direction designated by the parameter. | |||
data = nn:d |
|
|
| The unit is set to STILL mode upon completion of the | |||
nn = | Alarm number |
| search. | ||||
d = | F: | Forward direction |
| If the designated position is an illegal position (that is, the | |||
| N: | Reverse direction |
| target position does not exist), error code ERT is returned | |||
|
|
|
|
| from the unit, and the STOP mode is established. | ||
|
|
|
|
| If the OSP (STOP) command or OEJ (tape EJECT) | ||
|
|
|
|
| command is assigned during operation, error code ERI is | ||
|
|
|
|
| returned from the unit. | ||
|
|
|
|
| If the unit’s operation mode has been changed by an | ||
|
|
|
|
| operation at its front panel, error code ERF is returned from | ||
|
|
|
|
| the unit. | ||
|
|
|
|
| If the tape reaches its start or end during operation, error | ||
|
|
|
|
| code ERP is returned from the unit. | ||
|
|
|
|
| When data differing from the reference data has been sent, | ||
|
|
|
|
| error code ERE is returned from the unit. | ||
|
|
|
|
| <Note> | ||
|
|
|
|
| This command is not acknowledged while a search control | ||
|
|
|
|
| command is being processed or while one of the following | ||
|
|
|
|
| modes is established. | ||
|
|
|
|
|
|
|
|
|
|
|
|
|
| EJECT, REC, REC PAUSE, REC CHECK, POWER OFF |
|
|
|
|
|
|
| ||
|
|
|
| ||||
| [STX] SCP:data [ETX] | [STX] SCP [ETX] | Searches the counter value designated by the parameter. | ||||
Parameter |
|
|
| Playback is started upon completion of the search. | |||
data = ghmmssff |
|
| If the designated position is an illegal position (that is, the | ||||
(CTL data referenced) |
| target position does not exist), error code ERT is returned | |||||
g = Blank : With a positive (+) |
| from the unit, and the STOP mode is established. | |||||
| value |
|
| If the OSP (STOP) command or OEJ (tape EJECT) | |||
– sign : With a negative |
| command is assigned during operation, error code ERI is | |||||
| value |
|
| returned from the unit. | |||
h = |
| Hours |
| If the unit’s operation mode has been changed by an | |||
mm = | Minutes |
| operation at its front panel, error code ERF is returned from | ||||
ss = | Seconds |
| the unit. | ||||
ff = | 00 (fixed): Frames |
| If the tape reaches its start or end during operation, error | ||||
|
|
|
|
| code ERP is returned from the unit. | ||
|
|
|
|
| When data differing from the reference data has been sent, | ||
|
|
|
|
| error code ERE is returned from the unit. | ||
|
|
|
|
| <Note> | ||
|
|
|
|
| This command is not acknowledged while a search control | ||
|
|
|
|
| command is being processed or while one of the following | ||
|
|
|
|
| modes is established. | ||
|
|
|
|
|
|
| |
|
|
|
|
|
| EJECT, REC, REC PAUSE, REC CHECK, POWER OFF |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
70