Panasonic AJ-HPX3700G manual 161

6.Recording Error

Display window	“00:00:00:11” appears in the time code
	display field. Even after recording is
indication	stopped, this display continues to blink
	until the next operation is performed.
WARNING lamp	Blinks 4 times per second while recording
	continues.
Tally lamp	Blinks 4 times per second while recording
	continues.
Viewfinder	The “REC WARNING” indicator lights up.
Warning tone	Beeps 4 times per second while recording
	continues.
	This indicates a failure either in the P2
	card recording or the recording circuit.
Warning description	This is displayed when attempting to
	record clips where the total quantity
	exceeds the upper limit (1000 pieces) for
	a single P2 card.
Recording/playback	The recording may stop or continue.
operation
	Confirm the recording/playback operation
Countermeasures	after turning off the power supply once
	and then turning it on again.
	If the recording cannot be performed
	normally, change the P2 card.

7.Low Wireless Signal Reception

Display window	No display.
indication
WARNING lamp	Blinks 4 times per second (during pause
	and recording).
Tally lamp	Blinks 4 times per second while recording
	continues.
Viewfinder	The “WIRELESS-RF” indicator lights up
	while recording continues.
Warning tone	Beeps 4 times per second while recording
	continues.
Warning description	This error indicates poor wireless audio
	reception conditions.
Recording/playback	Continues to operate without receiving
operation	the wireless microphone signal.
Countermeasures	Check the microphone power supply and
	the reception status of the wireless
	receiver.

8.Battery Nearly Empty

Display window	One of the bars in the battery remaining
indication	indicator starts blinking.
WARNING lamp	Blinks once per second.
Tally lamp	Blinks once per second.
Viewfinder	The “BATT” LED blinks.
Warning tone	Beeps 4 times per second.
Warning description	The battery is about to run out.
Recording/playback	Continues to operate.
operation
Countermeasures	Replace the battery as required.

9.P2 Card Nearly Full

Display window	One of the bars for remaining MEDIA
indication	capacity starts blinking.
WARNING lamp	Blinks once per second while recording
	continues.
Tally lamp	Blinks once per second while recording
	continues.
Viewfinder	The P2 card remaining capacity indicator
	blinks.
Warning tone	Beeps once per second while recording
	continues.
Warning description	The total remaining capacity of all the P2
	cards is 2 minutes or less.
Recording/playback	Continues to operate.
operation
Countermeasures	Replace the cards. If there is an empty
	card slot, insert a new card.

10. P2 Card Error		Maintenance
	If the error occurs during recording,
	“00:00:00:11” appears in the time code
Display window	display field. The indication continues to
	flash after recording is stopped and until
indication
	the next operation is performed. There is
	no indication if the error occurs during	and
	playback.
	If the error occurs during recording, the	Inspections
WARNING lamp	lamp flashes 4 times per second for a
	period of about 3 seconds after recording
	stops. The lamp does not light if the error
	occurs during playback.
	If the error occurs during recording, the
Tally lamp	lamp flashes 4 times per second for a
	period of about 3 seconds after recording
	stops. The lamp does not light if the error
	occurs during playback.
	A flashing “CARD ERR ” appears. In
Viewfinder	the actual indication the is replaced by
	the slot number of the P2 card that
	triggered the error.
	If the error occurs during recording, the
Warning tone	tone sounds 4 times per second for a
	period of about 3 seconds after recording
	stops. The tone does not sound if the
	error occurs during playback.
Warning description	An error has occurred while recording
	data to or playing data from a P2 card.
Recording/playback	Stop recording or playback.
operation
Countermeasures	Replace the affected P2 card.

Maintenance and Inspections: Warning System 161