ERROR LED display (continued)

No.

 

 

REMAIN

Status

Corrective Action

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

27

R

 

 

 

 

A Verify NG error has occurred

After clearing the error display,

 

 

OR

 

when the Verify function was

 

 

 

 

 

executed independently.

try copying the data again.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

An error occurs when the Verify

 

28

R

 

 

 

 

NG error occurred the time

After clearing the error display,

 

 

OR

 

before, operation was terminated

 

 

 

 

 

without checking it, and then the

try copying the data again.

 

 

 

 

 

 

 

 

 

 

 

 

 

power is turned on.

 

 

 

 

 

 

 

 

 

29

 

 

 

 

 

The sensor has detected

After ensuring the unit is away

 

 

 

 

OR

impact to the HDD, and an

from the source of impact keep it

 

 

 

 

 

error has occurred.

off for a while.

 

 

 

 

 

 

 

 

To clear the error display, press the [POWER] button and [CANCEL] button together.

No.

 

 

 

 

 

COPY STATUS

Status

Corrective Action

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

During P2 card

 

30

R

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

access, the P2 card

Turn the unit OFF and ON.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OR

OR

OR

OR

OR

was pulled out and an

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

error occurred.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ENGLISH

Troubleshooting

If the unit seems to be malfunctioning, try checking the following points. If the problem persists, contact the place of purchase.

SymptomWhat to Check

The POWER LED does not light after the

• Is the battery pack drained?

[POWER] button is pressed.

• Is the AC adapter connected correctly?

 

 

 

 

Copying does not start after a P2 card is inserted

• Is there enough space for copying on the internal HDD?

• Is an error displayed indicating that internal HDD

and the [START] button is pressed.

temperature is over or under the prescribed level?

 

 

 

The [REMAIN] LEDs do not light after the [

 

]

• Is the POWER LED lit (green)?

 

 

button is pressed.

 

The [REMAIN] LEDs do not light after the [HDD

• Is the POWER LED lit (green)?

CAP] button is pressed.

 

 

 

 

• Is the unit processing copy or format operations?

 

 

 

• Does the computer support USB 2.0 connections?

The unit's internal drive letters are not displayed in

• Is the operating system Windows XP SP2 or later, or

Windows Explorer when the unit is connected to a

Windows 2000 SP4 or later?

• Is the unit correctly connected to the computer?

computer with the USB 2.0 cable.

• Is the network drive assigned a letter immediately

 

 

 

 

 

 

after the letters of the computer's hard drive or CD-

 

 

 

ROM drive?

 

 

 

 

P2 cards cannot be formatted.

• Is the write-protect switch set to PROTECT?

• Is the P2 card inserted correctly?

 

 

 

 

 

The POWER LED merely flashes after the

• Are you attempting to turn the unit ON in

[POWER] button is pushed.

temperatures below 5 °C (41 °F)?

 

 

 

 

E-28