External interfaces, RS-422 connector | Panasonic AV-HS400AN

6. External interfaces

This unit comes with RS-422, GPI and tally connectors to serve as external interfaces.

6-1. RS-422 connector

This enables the unit to be controlled by an external device.

Use it with the settings below. (D-sub 9-pin, female, inch screw)

Baud rate:	38400 bps				Pin assignment
Parity:	ODD				Pin No.	Signal name	Description of signal
Stop bit:	1 bit				1	FRAME GROUND	Frame ground
Stop bit:	1 bit				2	TXD –	Send data (–)
					2	TXD –	Send data (–)
	5 4	3	2	1	3	RXD +	Receive data (+)
	9	8	7	6	4	GROUND	Ground
					5	NC	Not used
					6	GROUND	Ground
					7	TXD +	Send data (+)
					8	RXD –	Receive data (–)
					9	FRAME GROUND	Frame ground

The following lists the functions which can be controlled by editing controller AG-A850. (Compliant with the GVG protocol)

•Crosspoint switch

•Wipe pattern selection (BKGD)

•Transition mode (MIX/WIPE) selection

•Auto transition time setting

•Auto transition execution

<Table of wipe patterns supported>

	GVG protocol		AV-HS400AN		GVG protocol		AV-HS400AN		GVG protocol		AV-HS400AN		GVG protocol		AV-HS400AN
	A	B	AV-HS400AN		A	B	AV-HS400AN		A	B	AV-HS400AN		A	B	AV-HS400AN
	A	B			A	B			A	B			A	B
	0 ]	1	WIPE #1		12	13	SQ #1		24	25	SL #1		36	37	3D #1
	1	2	WIPE #2		13	14	SQ #2		25	26	SL #2		37	38	3D #2
	2	3	WIPE #3		14	15	SQ #3		26	27	SL #3		38	39	3D #3
	3	4	WIPE #4		15	16	SQ #4		27	28	SL #4		39	40	3D #4
	4	5	WIPE #5		16	17	SQ #5		28	29	SL #5		40	41	3D #5
	5	6	WIPE #6		17	18	SQ #6		29	30	SL #6		41	42	3D #6
	6	7	WIPE #7		18	19	SQ #7		30	31	SL #7		42	43	3D #7
	7	8	WIPE #8		19	20	SQ #8		31	32	SL #8		43	44	3D #8
	8	9	WIPE #9		20	21	SQ #9		32	33	SL #9		44	45	3D #9
	9	10	WIPE #10		21	22	SQ #10		33	34	—		45	46	3D #10
	10	11	WIPE #11		22	23	—		34	35	—		46	47	3D #11
	11	12	WIPE #12		23	24	SQ #12		35	36	—		47	48	3D #12

]: Set “No. 256” when control is to be exercised from the AG-A850.

On the System sub menu of the SYSTEM menu, set On or Off for control from the external device (editor) connected to the RS-422 connector.

For details on the settings, see 5-6-2.

100

Image 100

Panasonic AV-HS400AN manual External interfaces, RS-422 connector

Contents

Operating Instructions Safety precautions FCC Note Important Safety Instructions For USA-California Only Contents Input/output signal settings System settings Features Description Precautions for use  Power indicator Power 2Alarm indicator AlarmSystem/Alarm 8/16 Functions in each area Crosspoint area Wipe area User button area = User buttons User 1, User Transition area Auto button CUT buttonFTB button PinP button Rotary encoders F1 to F5 LCD menu areaList of menu delegation functions Positioner area Positioner X/YRotary encoder Z Positioner Rotary encoder Valid menu SD memory card access LED SD memory card areaPSD memory card slot    Concerning the recommended SD memory cards SDI signal input connectors SDI Inputs 1 to SDI signal output connectors SDI Outputs PGM, 1Reference input connector/BB output connector REF External synchronization mode Tally output connector Tally D-sub 15-pin, male, inch screw \ GPI input connector GPI 3.5 mm diameter stereo mini jackGround connector AC power input socket in AC 100 V to 120 Configuration Board Model number Function Where connectedSystem Table of optional boards Connections Example where the optional board is used Selecting the bus mode Basic operationsBackground transition Selecting the bus Selecting the transition mode Manual transition using the fader leverAuto transition Cut transition How to select the wipe patterns WipeSelecting the wipe pattern Table of wipe patterns  Setting the border and soft effect  Setting the border colorTo call the preset color Selecting the wipe direction Setting the wipe start position Pos, Y-Pos setting range  Setting the trimming  Setting the lighting effectModifying wipe Key Key, PinP and DSK prioritiesHow key composition works Background Key source Selecting the key type Lum luminance key/self keyLinear linear key/EXT key Chroma chroma key/self key  Selecting the key fill and key source signals Selecting the key fill signalSelecting the key source signal  Setting the fill matte color Key transitions Pattern examples Operation Parameter Description of setting Setting range Adjusting the luminance key and linear keyKey preview Adjusting the chroma key  Executing auto samplingPositioner Rotary encoder Z Tips for chroma key adjustments  Adjusting the chroma keyItem operations  Making other adjustments  Setting the edge color  Setting the key edgeKey decorations Masking the key signals Turn F2 to F5 to set the area to be masked  PinP combinations using the flying key Flying key PinP picture in picture Selecting the PinP materialPinP transitions PinP preview PinP adjustments  Adjusting the PinP position and size Select the dot by dot mode  Adjusting the density PinP decorations Trimming settings DSK downstream key Selecting the DSK type  Selecting the DSK fill signal and DSK source signal Selecting the DSK fill signalSelecting the DSK source signal Selecting the DSK material DSK transitions DSK adjustmentsDSK preview  Setting the edge DSK decorations Masking the DSK signals FTB fade to black Internal color signals Setting the color background Adjusting the colors  Calling the preset colors Setting freeze Freezing the input signalsDisplaying the freeze status Switching the AUX output  Selecting the output signals using the crosspoint buttons Preset memory Table of stored preset memoryTransition area Border Bkgd Wipe Chroma key Description of setting Initial value factory default KeyColor  Clear This is used to clear contents in the preset memory Frame memories Transferring images from the AUX bus SD memory cards Initializing the SD memory cards Saving data on SD memory cards Loading data from SD memory cards Characters which can be used for filenames Deleting files on SD memory cards Displaying the SD memory card information Setting the SDI input signals and analog input signals Input/output signal settingsSetting the frame synchronizer Setting the input mode System Mode InputList of input modes supported 576/50i 1080/59.94i Setting the analog input gain Setting the analog composite input signals Setting the up-converter option Input image Setting the DVI input signals option Setting the DVI input signalsAutomatic adjustment of the black level Automatic adjustment of the white level 1280  720  Fit-V1024 768 Fit-H Adjusting the DVI input signals Types of output signals Setting the output signalsConnector Signal type Output default Assignment Normal Assigning the output signalsDC down-converter Setting the sync signals Output video signal phase adjustment Adjusting the output signal phasePhase Video format Adjustment range Phase adjustment setup System standard 1H Output +1H Shortest Output +0.5H Signals Video effects Output signals Down-converterWhen the 1080/59.94i format is used Frame synchronizer Phase relationship between input signals and output signals For 1080/59.94i format Example Setting the screen layout Setting the multi view displayDisplay modes Division mode Upper-L, Upper-R These can be set to PGM, PVW, AUX or KeyOut Setting the tally displays Setting the split frame and charactersLUM 0%, 25%, 50%, 75%, 100%  User type setting procedure  Preset type setting procedureChanging the material names Setting the on-screen display OSD  Examples of OSD displays Setting the DVI output signals option  Setting the V ancillary data Setting the ancillary data Setting the embedded audio data Setting the down-converter SQ squeezeEC edge crop LB letter box  Setting the 169 squeeze mode System settingsSelecting the video format Setting the crosspoints Assigning signals to the crosspointsAssigning signals to the crosspoints Button Signal Abbreviation Description Setting the crosspoint switching Button Signal Description Setting the user buttons Setting the FTB buttonSetting method Button assignments  Setting the date Setting the date and time Setting the time Network settings Setting the IP addressSetting the subnet mask Setting the gateway Other settings Setting the LCD backlightSetting editor enable Setting the protocol Setting the GPI Camera control Functions that can be controlled from the unit Connection specifications AW-RP655N RS-422 RS-232C ConverterPin No RS-422RS-232C Converter  Connections for AW-HE100N, AW-PH405N or AW-PH360N AW-HE100N, AW-PH405N, AW-PH360N Pin No  Connections for AW-PH400P AW-IF400G Switch settingsAW-PH400P  Camera control settings  For controlling the lens zooming System settings Alarm status displays Status displays Displaying the version information and option information Control, Panel, Input, M/EIN-SL1, 2 option input slots 1 OUT-SL1, 2 option output slots 1 Initialization RS-422 connector External interfaces GPI connector Initial settingControl functions that can be assigned Function assigned Description of control Remarks Pin No Signal name Input/output Description of signal Example of tally connections Specifications Image transmission functionsConnections LAN straight cable How to install the software Setting the IP address OperationStartup Exit Transmitting images to the unit Transmitting images from the unit Setting menu table Parameter Adjust Adjust1Adjust2 Hue-Rad Sat-Rad Soft Cancel Border Width Soft Mode Type FillPosition Trim Manual Signal Mode ↓ AnaGain Signal Output Mode ↓Sync ↓ BBSetup GenLock System Phase Signal Mode ↓ Size ↓ Scale ↓ Signal Scale ↓ MovDet ↓ Sharp ↓Signal Chroma Ped Hue Signal Scale ↓ Delay ↓ Sharp ↓ Mode ↓ 169SQ Signal PosCont Speed Power ↓Alarm Power Fan Date Year Month Date Set ↓Time Hour Minute Second Set ↓ Appearance Unit inch mm Specifications and standard accessories Video delay time SDI outputsAnalog composite Input option Standard accessories Optional boards sold separately Appendix glossary Frame Memory FreezeFTB Fade to Black Genlock Preset Bus Preset MemoryPreview Program Bus Headquarters Government officeBroadcast Parts Information & Ordering Panasonic Canada Inc