Panasonic DMR-EZ49VEB manual Setting the Channels and Clock, Preparation, To cancel Auto-Setup

Setting the Channels and Clock

Preparation:

≥Turn on the mains for the television (and connected equipment) and select the appropriate AV input to suit the connections to this unit.

≥These are the first settings you make upon buying the unit. You don’t need to make these settings again.

TV’s remote control

 TV

DRIVE		VOL		CH
SELECT	AV
			TRACKING/V-LOCK/PAGE
1	2	3

STEP 3

1
					DVB Auto Setup
		to turn the unit on.
				CH	Channel					Quality
							Name		Type
				Scan	CH 21					68
				27	BBC ONE Wales			TV		9
	DVB Auto Setup starts. The unit			27	BBC 2W			TV		9
				27	BBC Radio Wales			Radio		9
				27	BBC NEWS 24			TV		9
	will search for the digital terrestrial				Searching...
	channels. This takes about			TV: 6
					Radio: 4		Data: 0
	5 minutes.
				RETURN
2 Power Save in Standby
				Power Save in Standby
	Function:
					Power Save
									On
	3, 4 to select “On”,
					From 0	:00		To 6		:00
	“On Timer” or “Off”, then				Saves standby power consumption
			CHANGE		by disabling Quick Start function and
	OK				AV2 loop-through in standby.
			OK	RETURN
	“On”:	It will go into the Power Save in Standby mode
		when the unit is in standby mode.
	“On Timer”: Press [3, 4, 2, 1] to set the start and stop time,
	“Off”:	then press [OK].
		It is possible to start quickly from the standby
		mode. (Quick Start mode)
		≥“Power Save in Standby” is set to activate during
		the setting time period.

–The features of the Power Save in Standby function when the unit is in standby mode are as below.

Power Save in Standby	Activated (On	Deactivated
	/ On Timer)	(Off)
Power consumption	Approx. 0.5W*2	Approx. 14W
Quick Start*1	Deactivated	Activated
Front display	Turns off	Stays lit
	(The clock display
	disappears.)
Watching the picture from the	Cannot do	Can do
digital satellite receiver
connected to the AV2 terminal

§1 The unit could take over 1 minute to switch ON from standby mode with Quick start deactivated.

This time could be reduced to less than 10 seconds with Quick start activated.

§2 When “RF OUT ( Aerial Signal )” is set to “Off” in the Setup menu (> 72)

3When setup has completed, the confirmation screen appears.

OK

(continued on the next page)

CH

45 6

78 9 PROG/CHECK

DELETE 0 INPUT CHAPTER

SELECT

RESET SLOW/SEARCH

SKIP/INDEXREW FF

STOP PAUSE PLAY

STATUSEXIT

				I
			U D		E
			G
			R		U
	T	O			F
					C
A					N
G					O
I
V					T
A					I
					N
N				OK	M
C
T					E
E
I					N
D					U
R

OPTIONRETURN

		MANUAL SKIP
		-10s		+60s
REC	REC MODE	EXT LINK	DIRECT TV REC
TEXT	STTL	DISPLAY	TIME SLIP
				JET REW

Tips

To cancel Auto-Setup

Press [RETURN ].

If the unit displays “No stations found!”

Press [1] to select “No” and press [OK]. Go to step 2. After you have performed steps 2–;, turn off the unit and confirm the cable or aerial input is connected to the RF IN terminal. Restart the Auto- Setup again (> 67, DVB Auto Setup by Signal Quality).

If the clock setting menu appears or the clock is not correct

Set the clock manually (> 14).

Restarting the Auto-Setup (> 67, DVB Auto Setup by Signal Quality)

To set the channel list best suited to your region (> 67, DVB Auto Setup by Region)

About the screen saver function When this unit is not operated for approximately 5 minutes while the screen is being displayed, the screen saver may be displayed.

You can turn this function off (> 69, Screen Saver).

13

VQT2J51