Panasonic DMR-EZ49VEB Recording from a Digital Satellite Receiver, Satellite receiver you have

Recording from a Digital Satellite Receiver

[RAM] [-R] [-R]DL] [-RW‹V›] [+R] [+R]DL] [+RW] [VHS]

Manual Recording

Preparation:

≥[RAM] If the disc is protected, release protection (> 64).

≥[VHS] Ensure accidental erasure tab is intact.

≥Connect a digital satellite receiver to this unit’s AV2 input terminals (> 11).

≥Set the “AV2 Input” to match the connected equipment in the Setup menu (> 71).

≥When the output signal from the external equipment is NTSC, change the “TV System” to “NTSC” in the Setup menu (> 70).

1With the unit stopped

INPUT	to select “AV2” for the digital
SELECT
satellite receiver you have
connected.

Linked timer recordings with external equipment (SKY Digital STB/digital satellite receiver) — EXT LINK

To record programmes from a SKY Digital STB/digital satellite receiver using timer programming

Preparation:

≥[RAM] If the disc is protected, release protection (> 64).

≥[VHS] Ensure accidental erasure tab is intact.

≥Make sure you connect the AV2 terminal of this unit to “VCR Scart Terminal” of a SKY Digital STB/digital satellite receiver with a 21-pin scart cable (> 11).

≥Set the “AV2 Input” and “Ext Link” to match the connected equipment in the Setup menu (> 71).

1Make timer programming on SKY Digital STB/digital satellite receiver.

–Refer to the equipment’s operating instructions.

2	DRIVE
	SELECT	to select the DVD or VHS

2 DRIVE SELECT

to select the DVD or VHS

drive.

–Insert a disc or video cassette with enough remaining blank space (> 7).

3 REC MODE

to select the recording mode.

4Select the channel on the digital satellite receiver.

drive.

–Insert a disc or video cassette with enough remaining blank space (> 7).

3	EXT LINK
	–	The unit turns off and “EXT-L” lights on the
		unit’s display to indicate timer recording
	–	standby has been activated.
		While the unit is in EXT LINK standby mode or
		recording, most operations on this unit are

5 REC

Tips

to start recording.

prohibited ([< OPEN/CLOSE], [Í/I] etc.).

Tips

To cancel the external control

Press [EXT LINK] to stop recording or to cancel linked timer recording standby (The unit turns on and “EXT-L” disappears.).

To skip unwanted parts

Press [;] to pause recording. (Press again to restart recording.)

≥[VHS] When recording is paused for 5 minutes or more, the unit returns to stop.

To stop recording

Press [∫].

Notes

≥This unit cannot record NTSC signals to discs that already have PAL signal recordings.

Manual timer recordings (> 33)

Notes

≥In order to prevent accidental operation, press [EXT LINK] to cancel the setting after recording is finished.

≥This function does not work when “TV System” is set to “NTSC” in the Setup menu (> 70).

≥This function does not work with some equipment. Refer to the equipment’s operating instructions.

≥The beginnings of recordings may not be recorded correctly in some cases.

≥When “Ext Link” is set to “Ext Link 2”, this function does not work if the input signal is NTSC system.

≥Programmes are recorded as one title on this unit when the end time of the earlier timer recording and the start time of the later timer recording are close to each other.

[RAM] To divide the titles, go to “Divide Title” (> 51).

≥When this unit is in EXT LINK standby (“EXT-L” is shown on the unit’s display), the TV Guide data cannot be downloaded.

≥While the unit is in EXT LINK standby mode or recording, AV1 output terminal outputs the signal which is input from the AV2 input terminal irrespective of “AV1 Output” setting (> 71).

≥(Except for [VHS] ) During EXT LINK standby mode or recording, playback is only available if you select the DVD drive in the step 2 above.

≥When “EXT-L” lights on the unit’s display, Direct TV Recording is unavailable.

31

VQT2J51