Adding Staples Optional | Panasonic DP-6530 specs

5. ADDING STAPLES (OPTIONAL)

When the staple cartridge runs out of staples, if the optional finisher is installed, the following message appears:

Set staple cartridge

Add staples to the cartridge according to the procedure below.

Finisher (DA-FS810/FS815)

1

2

Open the front cover of the finisher.

Lower the blue lever in the stapler and slide out the staple cartridge.

-The stapler unit has moved to its specified position.

-Do not move the stapler unit while performing the above

7	procedure, or it will be broken.

3 Remove the empty staple case upward from the staple cartridge.

4 Push in a new staple case into the staple cartridge completely inside until a click is heard.

-Do not remove the seal holding the staples until the staple case is set in the cartridge.

7-20WHEN THE GRAPHIC SYMBOLS FLASH ON THE TOUCH PANEL

Image 148

Panasonic DP-6530 manual Adding Staples Optional

Contents

Operating Instructions Use of Recycled Paper in the Machine FCC Notice Off Mode Off Mode Default TimeAutomatic Energy Save Default Time Automatic Energy Save User Safety Preface Features of the DP-6530/8130 Preface Table of Contents Table of Contents Maintenance Disclaimer Notice Precautions Installation Precautions General PrecautionsBe sure to disconnect the power-cord plug Handle and use the machine gently and carefully High Temperature Warning Areas Fixing the adjusters stoppers Page Before Making Copies Main Components Back Side of the Control Panel Optional Equipment Configuration Optional EquipmentHole punch unit DA-SP81 External LCF Large Capacity Feeder DA-MA810 Control Panel Timer Lamp Function Clear keyStop key Start key Message Display Touch PanelTouch-keys Settings set functions confirmation key Clearing the Functions Selected Turning on the Power Switch Turning on the Power Switch/Auto Job StartTurning on the Power Switch Turn on the power switch When Ready appears, the machine is ready for copying Controlling the Use of the Machine with Department Codes After Copying is FinishedPage HOW to Make Copies General Copying Procedures When Coming Across the Situations below Exiting Copy Papers Acceptable Copy Paper Types and Sizes Setting Copy PaperFeeder Paper Type Paper Size Remarks Handling and Storing Paper Pay attention to the following points Setting Copy Paper Setting the Drawer for Special Uses If you want to select the Cover , Insert or TAB Paper Setting Originals Acceptable Original Types and Sizes Setting Originals When Placing an Original on the Glass When Using the Reversing Automatic Document Feeder Exiting Originals Continuous Feed Mode After aligning the edges of originals well, placeOriginals Them face up and align the slides to the width Auto JOB Start JOB Preset Confirming and Cancelling Auto Job StartPlace the originals. Confirming auto job start Interrupt Copying Press the Interrupt keyReplace the original with a new one. Interrupt key again Stopping the Copy Operation Deleting or Changing Order of Pending Jobs Deleting the Job Changing order is completed 18HOW to Make Copies Setting of Basic Copy Modes Paper Selection Automatic Paper Selection APS Manual Paper Selection Reduction and Enlargement Copying Press the AMS key Press the key corresponding to the original size Paper size, then press the ZOOM···· key Reduction and Enlargement CopyingPress the drawer icon representing the desired copy Duplex Copying 1-SIDED, 2-SIDED, BOOK-TYPE Duplex Copying 1-SIDED, 2-SIDED, BOOK-TYPE Follow the same procedure 1 to 3 as shown aboveBook-Type Originals 2-Sided Copies Press the Book 2 key Select the book copying type Select LT copy size 10SETTING of Basic Copy Modes Copy Density Adjustment Manual Copy Density Mode Copy Density AdjustmentPress Auto on the basic screen Selecting Original Mode Quick Access Menu Using the Editing Functions Image Shift Providing Right or Left Margin Press the Start key Providing a Bookbinding Margin Edge Erase Press the 1 Side Or 2 Side key DUAL-PAGESelect the 1 Side Turn to the next page, set the book again DualScanned Y Zoom Press the lower SET key Image Editing Trimming/Masking Enter the distance values read in for the specified area Press the lower SET key Place the original. Sheet original Image Editing Mirror Image Negative/Positive Reversal 2IN1 4IN1 Select the type of image combination Select the type of the originalPlace the originals Key Copying with Annotation Numbering Copying Magazine Sort from the Editing Menu Adjust the binding margin and press the SET key Cover Copying TOP Copied Back Blank 7Press the Start key TAB Paper Mode Setting Tab Paper in the Drawer Pull the second drawer out Tab Width Adjustment Key, then adjust the tab extension tab width TAB Paper ModeShift width then press the SET key Place tab paper in the drawer or the bypass guide Tab Paper CopyingPress the Copy on TAB key Press the SET key Tab Paper Insertion Press the TAB Paper key Tab Paper Insertion and Copying Place tab paper in the drawer or the bypass guide Document Storage Press the Start key Overlay Entering letters. Page 5-29 Max characters Press the Overlay key OverlayPress the Start key Confirming Overlay Test Print Press the Start key Cancelling the Sharpness Adjustment Sharpness AdjustmentPress the Soft or Sharp key Direction of Duplex Copy Images Rotation Using Special Functions Continuous Original Feeding / Single Original Feeding Copying begins MIXED-SIZED Originals Storing a Combination of Copy Job Settings JOB Memory JOB Memory Confirming Stored Copy Jobs Bypass Copying Bypass copying Press the Start key Bypass Copying Bypass Copying on Standard Size PaperPerform steps 1 to 2 on pages 5-8 Set the Other size key as necessary. Bypass Copying on Non-Standard Size Paper Key in each dimension, then press the Memory key Storing a Non-Standard Size in the Memory Weekly Timer Set the ON/OFF times for each day of the week Setting the Other Size KEY Check that the settings are all correct Setting the Date and TimeSetting the Clock fore Daylight Saving Time Setting the Automatic Energy Save Mode Clearing the Automatic Energy Saving ModeAllowed before the Automatic Energy Saving mode is Activated Setting the Automatic OFF-MODE Clearing the Off-Mode/Sleep Mode Switching Languages Press the key of the desired language User Selection Initial settings Department Codes Input the master code name, and press the SET key Master code name is displayed in the department number Department Codes Registration / Change / Deletion of Department Code Entering letters 24USING the Special Functions Entering letters Page 5-29 Max characters Page Counter reset is completed Print out Department Code Entering Letters Entering Letters Entering Letters Page 32USING the Special Functions Selecting Finishing Modes Finishing Modes and Finishers Optional Names of the Main Components SORT/GROUP Copying Press the Sort or Group key Staple Sorting Optional DA-FS810/FS815 Maximum Number of Sheets that can be Stapled Magazine Sort & Saddle Stitch Mode Booklet Mode Press Start key Available Conditions for Saddle Stitch Hole Punch Mode Optional Number of punch holes and available paper sizes When the Graphic Symbols Flash on the Touch Panel Description of the Flashing Graphic Symbols ADD Paper Symbol Adding Paper to the DrawersPull the drawer out carefully until it comes to a stop Place the paper in the drawer ADD Paper Symbol Adding Paper to the Tandem LCF Large Capacity FeederPull the tandem LCF out carefully until it comes to a stop Close the cover of the tandem LCF Place the paper on the elevator tray Close the cover of the external LCF Replace Toner Bottle Symbol Open the front cover Shake the new toner bottle well to loosen the toner inside Replace Toner Bottle Symbol Additional ExplanationDispose of Used Toner Replace Toner Bag Clear Paper Symbol Clear Paper Symbol Lift the blue handle second as shown on the right Remove any misfed paper Open the bypass cover Remove any misfed paper Open the exit coverTurn the handle in the direction of the arrow Pull the transfer unit out until it comes to a stop Lift the grip, then turn the knob in the directionArrow to remove any misfed paper 11Remove any misfed paper Blue knob Return the external LCF to its original position Paper Misfeed in the Hole Punch Unit Optional Knob 18WHEN the Graphic Symbols Flash on the Touch Panel Page Adding Staples Optional Adding Staples Optional Close the front cover of the finisher Saddle Stitch Unit Page Removing Jammed Staples Optional Return the staple case to its original position Removing Jammed Staples Optional Disposing of Accumulated Punched Paper Bits Optional Call Service Symbol / Periodic Maintenance Message Maintenance Weekly Maintenance Power switch ON/OFF statusDaily Inspection Items for Daily Check Simple Troubleshooting Display does not change when keys or icons are pressedMachine does not start Copy density is too low Simple Troubleshooting Copy density is too highCopies are stained Copy images are blurred Specifications Options DP-6530/8130 Specifications OPC Continuous Copying Speed Finishers Specifications of OptionsTray Loading Capacity Hole Punch Unit External LCF Large Capacity Feeder Packing List Index Numbers Index When Using the Reversing Automatic Document Memo Page USA Only