Error messages, Display message | Panasonic KX-TG7841UE guide

Useful Information

Error messages

Display message

Base no power

or

No link. Re-connect base AC adaptor.

or

No link.

Busy

Call phone company for your access #

Check tel line

Error!!

Failed

Invalid

Requires subscription to Caller ID.

Cause/solution

RThe handset has lost communication with the base unit. Move closer to the base unit and try again.

RUnplug the base unit’s AC adaptor to reset the unit. Reconnect the adaptor and try again.

RThe handset’s registration may have been canceled. Re-register the handset (page 66).

RWhen “No link.” is displayed during a power failure, place a handset on the base unit to supply power to the base unit.

RNo cellular phone is paired to the base unit. Pair a cellular phone (page 14).

RThe called unit is in use.

ROther unit is in use and the system is busy. Try again later.

RThe handset you are using is too far from the base unit. Move closer and try again.

RYou have not stored the voice mail access number. Store the number (page 55).

RThe supplied telephone line cord has not been connected yet or not connected properly. Check the connections (page 8).

RIf you do not connect the telephone line cord and use only cellular lines, set the cellular line only mode (page 16).

RRecording was too short. Try again.

RSomeone is using a cellular line or headset. Try again later.

RThe phonebook copy is incomplete (page 45). The cellular phone is disconnected from the base unit. Make sure that other Bluetooth devices are not connected to the cellular phone, and try again.

RAlthough the unit tried to connect to the cellular phone or headset, the connection has been failed.

–Someone is using a cellular line or headset. Try again later.

–Make sure that the cellular phone or headset is not connected to other Bluetooth devices.

RThe handset is not registered to the base unit. Register the handset (page 66).

RYou must subscribe to a Caller ID service. Once you receive caller information after subscribing to a Caller ID service, this message will not be displayed.

59

TG7841BX_UE(en)_0528_ver011.pdf 59

2013/05/28 18:56:50

Image 59

Panasonic KX-TG7841UE, KX-TG7841BX operating instructions Error messages, Display message, Cause/solution

Contents

Thank you for purchasing a Panasonic product KX-TG7841UE Table of Contents Additional/replacement accessories Accessory informationSupplied accessories Trademarks Bluetooth devicesYour Bluetooth cellular phone*1 2 max Your Bluetooth headset*1 1 max For your safety Base unit location/avoiding noise Important safety instructionsBattery For best performance Routine care SpecificationsOther information Connections Setting upBattery installation Battery charging Operation Operating time Intelligent eco modeBattery level Icon Battery level Mholdn ControlsMoffn Mflashnmcall Waitn Mnoise Reductionn Handset display items Display/IndicatorsBelt clip Base unit display items Cell 1/CELL 2 indicators on the base unit Date and time Initial settingsDialing mode Moffn Link to cell featurePairing a cellular phone Unpairing a cellular phone Auto connection to the cellular phone Link to cell settingsRing as cell mode Selecting which unit receives cellular calls When you use the landline again Cellular line only mode If you do not use the landlineConnecting/disconnecting the cellular phone manually Msaven a Mexitn Changing the Bluetooth PIN Personal Identification NumberCellular line selection Storing your area code for a local call Making landline calls Making cellular calls Hold Useful features during a callAnswering calls For call waiting or Call Waiting Caller ID service usersHandset noise reduction Flash for landline calls MbN Transfer to cell a Using the other line during a conversationCall share To hold the 2nd call Mmenun a MbN Hold a Mselectn Power back-up operation for landlineMaking calls during a power failure Making a call using the redial list Answering calls during a power failure Mexitn Adjusting the speaker volumeMaking a cellular call using the redial list Mredialn While the base unit is ringing for an incoming call For call waiting or Call Waiting Caller ID service users MZN To switch between calls, press Mcall Waitn Key Character GroupsCharacter table for entering names Erasing the character or number Mokn Searching by first characterSearching by query Searching by group Erasing an entry Editing entriesErasing entries Chain dial Speed dial Main menu Answering device Programmable settingsDisplay menu tree and direct command code table Handset Greeting Record greeting Settings Ring count RingsPlay all msg Erase all msg Add new Disconnect BluetoothDevice *3 Ringer volume Link to cell Connect Time adjustment*9 Caller ID auto Settings Auto connect MinMode Cell line select Cellphone 1*3 Alarm Once Set date & time Date and time Time adjustment *9 Caller ID autoVoice mail *2 Store VM access# Set tel line *2 Set dial mode Pulse Base unit Start/End Talking CID *6 On Off Main menu Initial settingNight mode On Off Interrupt tone *6, *10 On Off Special programming AlarmNight mode Turning night mode on/off MbN Call block a Mselectn MbN Yes a Mselectn Storing unwanted callersFrom the caller list Handset Mcidn Area Setting the first ring for the call block listBlocking incoming calls without phone number Viewing/editing/erasing call block numbers Ringer ID for handset Using Caller ID serviceCaller ID features Talking Caller ID MbN Group a Mselectn Using a cellular line HandsetCaller list Viewing the caller list and calling back To erase your area code Editing a caller’s phone number before calling backErasing selected caller information Mselectn Moffn Erasing all caller information To copy from other cellular phones not paired Setting conversion codesWhen Select mode menu is displayed Copying phonebook from a cellular phone phonebook transfer Unpairing a headset Pairing a headset to the base unitOperating a Bluetooth wireless headset using a landline Connecting/disconnecting a headset Answering landline calls with your headset Switching between the base unit and your headsetAdjusting your headset receiver volume To switch to the base unit Press MZN on the base unit Memory capacity including your greeting message Answering system for landlineTurning the answering system on/off Greeting message Listening to messages using the base unit Editing the number before calling back Listening to messages using the handsetErasing all messages Operating the answering system New message alert by a call Alerting featuresAdvanced new message Audible message alert Remotely Remote access codeUsing the answering system Remote operation Turning on the answering system remotely Answering system settingsRemote commands Voice guidance Selecting Greeting only Caller’s recording time Listening to voice mail messages Voice mail service for landlineStoring the voice mail VM access number To erase the voice mail access number Making an intercom call IntercomHandset locator Transferring calls, conference calls To establish a conference call Press Mconfn Answering a transferred callMbN Stop conference a To complete the transfer Press MZN Wall mounting Display message Error messagesCause/solution General use TroubleshootingUse rechargeable battery Problem Making/answering calls, intercom Battery recharge Can make and answer cellular calls but cannot hear a sound Caller ID/Talking Caller ID Using Bluetooth devices Answering system Bluetooth PIN Deregistering a handset Liquid damageRegistering a handset to the base unit Index For your future reference