How to Operate NE-2156-2/NE-1656

To Release Program Lock:

PAD

INSTRUCTION

DIGITAL DISPLAY WINDOW

1

Open the door and leave it open.

 

The oven lamp will turn on, and “0” will appear.

2

+

While pressing Stop/Reset pad, press Prog pad until “PROG” and

PROG

 

“P” appear. (more than five seconds)

 

 

 

“PROG” and “P ” will appear.

 

 

 

 

 

In Program Unlock mode:

Oven reverts to a two-touch operating mode (Number/Memory pad + Start pad).

Repeat and interrupt feature are operational.

Number/Memory pads can be programmed.

Tone loudness control and length control are operational.

F. BEEP TONE

The loudness of beep tone and the length of beep tone at the end of heating cycle can be set.

There are four levels of the loudness. The level is indicated by a number followed by the word “bEEP”. 3bEEP = loudest

2bEEP = middle 1bEEP = quietist 0bEEP = silent

There are two options of the length of beep tone at the end of heating cycle. The length is indicated by 1 st or 2 nd Stage Heating Indicator.

1 = 3 beeps

2 = short beeps for 60 seconds

The loudest level and 3 beeps are preset at the factory.

To Select Loudness Level and Length “3 beeps”:

Example: To select loudest beep tone

PAD

INSTRUCTION

DIGITAL DISPLAY WINDOW

1

Open the door and leave it open.

 

The oven lamp will turn on and “0” will appear.

 

2

 

 

 

 

 

 

 

Press Prog pad.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3

 

 

 

 

 

 

 

Press Number/Memory pad “0” once.

 

PROG

 

0

 

 

The tone will sound at its loudness level and the loudness level “3”

 

 

 

 

 

 

 

 

 

 

 

 

followed by the word “bEEP” will appear. “PROG” will start to blink and

1

 

 

 

 

 

 

 

 

 

 

1st Stage Heating Indicator “1” (the length of beep tone “3 beeps”) will

 

 

 

 

 

 

 

 

 

 

 

 

be indicated.

 

 

 

 

 

 

 

 

 

 

 

 

Note: Repeating to press the pad “0” will lower the loudness all the way

 

 

 

 

 

 

 

 

 

 

 

 

to silent. (3 bEEP –– loudest, 2 bEEP –– middle,

 

 

 

 

 

 

 

 

 

 

 

 

1 bEEP –– quietest, and 0 bEEP –– silent)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4

 

 

 

 

 

 

 

Press Prog pad.

 

PROG

 

 

 

 

 

 

 

 

 

 

“PROG” will stop blinking. That means that you have completed

 

1

 

 

 

 

 

 

 

 

 

 

program.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Three seconds later, “0” will appear.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

• Close the door. One minute later, Digital Display Window will go blank.

- 10 -