Procedure of lamp unit replacement | Panasonic PT-DW100E specs

Procedure of lamp unit replacement

1.Turn the main power OFF, following the procedures described in “Powering up the projector” (p. 36) and “Powering off the projector” (p. 37), disconnect the power plug from the AC power source, and wait for one hour or more. Then check around the lamp unit that has cooled down.

2. Use a Phillips screwdriver to	Lamp unit cover screw
loosen the lamp unit cover screw
at the rear of the projector until
the screw turns freely.

3. Open the lamp unit cover and remove it from the projector.

		Lamp unit cover
	4. Use a Phillips screwdriver to
	loosen the three fixing screws for	Fixing	Handle
	the lamp unit to be replaced until	screws	Handle
	the lamp unit to be replaced until	screws
	the screws turn freely. Hold the
	handle of the lamp unit and gently
	pull the lamp unit out from the
	projector.
	CAUTION
	The lamp unit and structural parts around the
	lamp unit will be hot immediately after the
	projector has been used.
	You might get burned if you touch it while it is still
	hot.	Lamp unit 2	Lamp unit 4
		Lamp unit 2	Lamp unit 4
		Lamp unit 1	Lamp unit 3

5.Install the new lamp unit.

6.Use a Phillips screwdriver to securely tighten the 3 lamp unit fixing screws for each lamp unit.

7.Install and close the lamp unit cover, and then use a Phillips screwdriver to securely tighten the lamp unit cover screw.

Caution

•Firmly install the lamp unit and lamp unit cover. If not installed firmly, a protection circuit will function and the power will not be turned on.

Lamp unit cover screw

Lamp unit cover

Information

ENGLISH – 113

Image 113

Panasonic PT-DW100E Procedure of lamp unit replacement, Lamp unit to be replaced until, Lamp unit cover screw

Contents

Operating Instructions Dear Panasonic Customer Contents Important Safety Notice Fuse Important the Moulded Plug U.K. onlyGetting Started Page „ Do not place liquid containers on top of the projector „ Do not disassemble the lamp unit„ Do not insert any foreign objects into the projector „ Do not place sets directly on top of each other English English Accessories Before UsingDo not place the projector on a vinyl sheet or carpet 76, to on Disposal „ Maintenance„ To view clear images „ Lamp Remote control operation indicator lamp Remote control unitLocation and function of each part „ Front „ Bottom Remote control transmitter window„ Side Projector Main Unit Remote control receiver window front„ Rear Burglar hook Self-diagnosis display ･･･････････ pp Light ON/OFF button „ ControlsConnection Terminals p Controls „ Connection terminals Loading batteries Using the remote control unitEffective range of remote Control operation Using a wired remote Control Setting projector ID Number to remote control Examples of system expansion Installation Installation geometry Adjusting the feetLens Dimension of L1 Approx Projection scheme Side View Top View StartedGetting For the screen aspect ratio of 169 Units m „ Calculation formulas for projection distance by lens types Dimensions applying when Installation dimensions diagram Connection Pin No SignalBefore starting connection Pin No Control PC Video deck TBC built-in Example of connecting with Video devices Example of connecting with personal computers Installing the input module Installation of input module optionalModule Module model Terminal Signal formats supported „ Types of the input modules optional Fix the input module Register the input signal „ Procedure of installationRemove the slot cover Insert the input module DVI-D ET-MD77DV Connecting signals to the input module Connecting the signal to the HD/SD-SDI input module Connecting the signal to the SD-SDI input moduleSD-SDI input module optional HD/SD-SDI input module optional Dual link HD/SD-SDI input module optional DVI-D input module optional Connecting signals to the DVI-D input modulePin Signal How to remove Projection lens How to install Projection lens Connecting the power Cord Power indicator lampIndicator Projector status Status Projection Press Power on Powering up the projectorMaking adjustment Selection Press Power Standby Powering off the projector How to adjust the focus, zoom and shift How to adjust the lensPress to select an item and adjust it „ Using the remote control Model number of projection lens Adjustment range after lens position optical shiftMoving the projection lens position to the home position Illustration of influence of lens orientation „ About the focus balance English Precautions for projector installation work Registration of new data Registration of input signal dataDisplayed Press Enter Press Default Clearing the data Registered signals„ How to register into sub memory Sub memory Restrictions „ How to erase sub memory„ On-screen indications Switching the input signal Using the Shutter FunctionOn-screen display Function Status function Using the FUNC1 button Automatic adjustmentTurning on button Illumination Displaying the internal Test pattern Changing the picture Aspect ratio Press Aspect on the remote control „ Picture pp On-screen menusIcon Main Menu item Select the item to be set „ P in P pp „ Test Pattern p „ Signal List pp „ Security pp „ Projector Setup pp„ Position pp „ Advanced Menu pp Resetting to the factory Default Using the menu screens Adjusting Contrast Adjusting the pictureSwitching the picture mode Adjusting Colour Adjusting BrightnessAdjusting Tint Adjusting the colour Temperature Press to switch Color Temperature Gamma settingPress to switch Gamma Press to select Gamma Dynamic iris setting Sharpness settingNoise reduction setting Registering the picture mode Settings as presettings Display the Picture screen. p Press to select Picture To display pictures complying With the sRGB standardPress to select Natural Press to select Color ET-MD100SD4 Shift adjustment Adjusting the position„ For vertical up and down adjustment Press to select Shift Press to select Aspect Adjusting the aspect ratioPress to switch Aspect Keystone distortion Correction Adjusting the zoom ratioClock phase adjustment Press to adjust the correction amount Blanking adjustment How to use Advanced MenuPress to switch Digital Cinema Reality Digital cinema reality Adjusting the clamp Position Adjusting the input Resolution Edge blending adjustment Press to select Bright Inside Press Enter Frame delayPress to select Frame Delay Press to adjust the position Press to switch Frame DelayRaster position Press to select Raster Position Changing the display Language Setting the Display LanguagePress to select the desired language Display Language Adjusting colour matching Display Option settingsPress to switch Color Matching Press to select Color Matching Press to adjust the values Using a colorimeterPress to select Measured Data Press Enter Press to select Target Data Large Screen Correction RGB in Only RGB input Press to switch DVI Press to switch DVI EdidPress to select DVI-D Wide AUX DVI in Only when ET-MD77DV is installed Features On-Screen display settingSpecial Back Colour Press to switch Back Color Setting the startup logoPress to switch Startup Logo Press to select Startup Logo Setting a projector ID Projector setupProjector Setup Press to select Projector ID Direction Installation SettingAltitude Mode Press to select Lamp Select Press to switch Lamp SelectLamp select Lamp relay RS-232C settingRemote2 mode Status Cleaning the air filterPress to select Status Press to move to the next Press to switch Time Auto power offPress to select Auto Power OFF Press to switch Auto Power OFF Save all user data Setting FUNC1Setting the date and time Load all user data Service passwordInitialize Press to select Load ALL User Data Setting the P in P function Using the P in P functionPress to select P in P Mode USER1, USER2, USER3 SUB Window Main WindowFrame Lock Type „ Cycle of displayed internal test Patterns Displaying the internal test patternPress to select Test Pattern Displaying the security Screen Setting the securitySetting the security Password Changing the text Changing the security PasswordSetting the text Press to select Control Device Setup Control device setupPress to select Control Panel or Remote Controller Remote Controller Network standby How to use network functionInitial setting of network Function Network status Network controlPress to select Network Press to select Network Status „ Name and function of network function parts Network connectionsLAN LINK/ACT lamp green LAN10/100 lamp yellow Press OK to display the Projector status Accessing from the Web browser„ Change Password „ Basic control Detailed set up buttonSelection tabs Monitor information button „ Detail control Lens adjustment Test pattern display„ Projector status Menu display Parameter Description „ Error informationOK Normal operation Failed Occurrence of trouble „ E-mail setup English English „ Ping test „ Authentication set up „ Contents of mail sent „ Network config „ Adjust clock „ Firmware update Supported commands Using the PJLink protocol„ PJLink security authorization Command Control details „ Pin assignments and signal names Using the serial terminals„ Communication conditions Factory setting Examples of connection „ For RS-422 Pin Signal Description No. nameSignal level RS-422-compliant Basic format Control commandsCommand Function of command Remarks „ When multiple projectors are connected Cable specifications„ Connecting to a PC Example of a control panel layout Using the Remote 2 terminalPin assignments and control Names of terminals Open H Short L Lamp Indication of monitor lamp Procedure of cleaning Cleaning and replacement of air filter Install the brush cover so that it Install the movable metal meshFilter to the filter cleaning unit Precautions on lamp unit replacement Replacement of lamp unitTiming of lamp unit replacement „ Indication after 1 800 hours Lamp unit cover screw Procedure of lamp unit replacementLamp unit to be replaced until Installation procedure Power does not turn on Symptoms Check point Details Remedy Self-diagnosis display FF0 PT-DW100E SpecificationsModel No RGB2 input Appendix Compatible Signals MAC21 Subwindow List of P in P Outside dimensions Dimensions Index Wired remote control ･･････････････････････････ For business users in the European Union Trademark Acknowledgement