Press to adjust the correction amount | Panasonic PT-DW100E instruction

3.Press ◄► to adjust the correction amount.

•The value changes from -127 to 127.

4.Press ▲▼ to select “SUB KEYSTONE” or “LINEARITY”.

5.Press ◄► to adjust the correction amount.

•The value changes from -127 to 127.

Note

•Adjust the “SUB KEYSTONE” or “LINEARITY” after adjusting the “KEYSTONE”.

The variable range of the “SUB KEYSTONE” or “LINEARITY” changes in response to the adjusted value of the “KEYSTONE”.

•“SUB KEYSTONE” is a function which is used to correct keystone distortion when the lens has been shifted to the left or right. Keystone correction can only be carried out for the area at the top-right of the screen. However, this adjustment cannot be used when “KEYSTONE” is set to “0”.

•Pressing DEFAULT of the remote control will restore the factory default (“KEYSTONE”: 0, “SUB KEYSTONE”: 0, “LINEARITY”: 0).

•The adjusted value is reflected in other input signals.

•Keystone distortion can be corrected to ±40°of the angle of tilt for the projector against the screen. (The range for the angle of elevation is within ±22° when using a lens with a fixed focal point, and it is within ±28°when using an LE6 lens.)

•If keystone correction is used, edge blending adjustment cannot be performed properly.

Basic Operation

ENGLISH – 61

Image 61

Panasonic PT-DW100E operating instructions Press to adjust the correction amount

Contents

Operating Instructions Dear Panasonic Customer Contents Important Safety Notice Getting Started Important the Moulded Plug U.K. onlyFuse Page „ Do not place liquid containers on top of the projector „ Do not disassemble the lamp unit„ Do not insert any foreign objects into the projector „ Do not place sets directly on top of each other English English Accessories Before UsingDo not place the projector on a vinyl sheet or carpet 76, to on Disposal „ Maintenance„ To view clear images „ Lamp Remote control operation indicator lamp Remote control unitLocation and function of each part „ Front „ Side Remote control transmitter window„ Bottom Projector Main Unit Remote control receiver window front„ Rear Burglar hook Connection Terminals p Controls „ ControlsSelf-diagnosis display ･･･････････ pp Light ON/OFF button „ Connection terminals Effective range of remote Control operation Using the remote control unitLoading batteries Using a wired remote Control Setting projector ID Number to remote control Examples of system expansion Installation Installation geometry Adjusting the feetLens Dimension of L1 Approx Projection scheme Getting StartedSide View Top View For the screen aspect ratio of 169 Units m „ Calculation formulas for projection distance by lens types Dimensions applying when Installation dimensions diagram Connection Pin No SignalBefore starting connection Pin No Control PC Video deck TBC built-in Example of connecting with Video devices Example of connecting with personal computers Installing the input module Installation of input module optionalModule Module model Terminal Signal formats supported „ Types of the input modules optional Fix the input module Register the input signal „ Procedure of installationRemove the slot cover Insert the input module DVI-D ET-MD77DV Connecting signals to the input module Connecting the signal to the HD/SD-SDI input module Connecting the signal to the SD-SDI input moduleSD-SDI input module optional HD/SD-SDI input module optional Dual link HD/SD-SDI input module optional Pin Signal Connecting signals to the DVI-D input moduleDVI-D input module optional How to remove Projection lens How to install Projection lens Connecting the power Cord Power indicator lampIndicator Projector status Status Projection Making adjustment Selection Powering up the projectorPress Power on Press Power Standby Powering off the projector How to adjust the focus, zoom and shift How to adjust the lensPress to select an item and adjust it „ Using the remote control Moving the projection lens position to the home position Adjustment range after lens position optical shiftModel number of projection lens Illustration of influence of lens orientation „ About the focus balance English Precautions for projector installation work Registration of new data Registration of input signal dataDisplayed Press Enter Press Default Clearing the data Registered signals„ How to register into sub memory Sub memory „ On-screen indications „ How to erase sub memoryRestrictions Switching the input signal Using the Shutter FunctionOn-screen display Function Status function Using the FUNC1 button Automatic adjustmentTurning on button Illumination Displaying the internal Test pattern Changing the picture Aspect ratio Press Aspect on the remote control „ Picture pp On-screen menusIcon Main Menu item Select the item to be set „ P in P pp „ Test Pattern p „ Signal List pp „ Security pp „ Projector Setup pp„ Position pp „ Advanced Menu pp Resetting to the factory Default Using the menu screens Switching the picture mode Adjusting the pictureAdjusting Contrast Adjusting Colour Adjusting BrightnessAdjusting Tint Adjusting the colour Temperature Press to switch Color Temperature Gamma settingPress to switch Gamma Press to select Gamma Noise reduction setting Sharpness settingDynamic iris setting Registering the picture mode Settings as presettings Display the Picture screen. p Press to select Picture To display pictures complying With the sRGB standardPress to select Natural Press to select Color ET-MD100SD4 Shift adjustment Adjusting the position„ For vertical up and down adjustment Press to select Shift Press to switch Aspect Adjusting the aspect ratioPress to select Aspect Clock phase adjustment Adjusting the zoom ratioKeystone distortion Correction Press to adjust the correction amount Blanking adjustment How to use Advanced MenuPress to switch Digital Cinema Reality Digital cinema reality Adjusting the clamp Position Adjusting the input Resolution Edge blending adjustment Press to select Frame Delay Frame delayPress to select Bright Inside Press Enter Press to adjust the position Press to switch Frame DelayRaster position Press to select Raster Position Changing the display Language Setting the Display LanguagePress to select the desired language Display Language Adjusting colour matching Display Option settingsPress to switch Color Matching Press to select Color Matching Press to adjust the values Using a colorimeterPress to select Measured Data Press Enter Press to select Target Data Large Screen Correction RGB in Only RGB input Press to switch DVI Press to switch DVI EdidPress to select DVI-D Wide AUX DVI in Only when ET-MD77DV is installed Features On-Screen display settingSpecial Back Colour Press to switch Back Color Setting the startup logoPress to switch Startup Logo Press to select Startup Logo Setting a projector ID Projector setupProjector Setup Press to select Projector ID Altitude Mode Installation SettingDirection Lamp select Press to switch Lamp SelectPress to select Lamp Select Remote2 mode RS-232C settingLamp relay Status Cleaning the air filterPress to select Status Press to move to the next Press to switch Time Auto power offPress to select Auto Power OFF Press to switch Auto Power OFF Setting the date and time Setting FUNC1Save all user data Load all user data Service passwordInitialize Press to select Load ALL User Data Setting the P in P function Using the P in P functionPress to select P in P Mode USER1, USER2, USER3 SUB Window Main WindowFrame Lock Type „ Cycle of displayed internal test Patterns Displaying the internal test patternPress to select Test Pattern Setting the security Password Setting the securityDisplaying the security Screen Setting the text Changing the security PasswordChanging the text Press to select Control Device Setup Control device setupPress to select Control Panel or Remote Controller Remote Controller Initial setting of network Function How to use network functionNetwork standby Network status Network controlPress to select Network Press to select Network Status „ Name and function of network function parts Network connectionsLAN LINK/ACT lamp green LAN10/100 lamp yellow „ Change Password Accessing from the Web browserPress OK to display the Projector status „ Basic control Detailed set up buttonSelection tabs Monitor information button „ Detail control Lens adjustment Test pattern display„ Projector status Menu display OK Normal operation Failed Occurrence of trouble „ Error informationParameter Description „ E-mail setup English English „ Ping test „ Authentication set up „ Contents of mail sent „ Network config „ Adjust clock „ Firmware update Supported commands Using the PJLink protocol„ PJLink security authorization Command Control details „ Pin assignments and signal names Using the serial terminals„ Communication conditions Factory setting Examples of connection Signal level RS-422-compliant Pin Signal Description No. name„ For RS-422 Command Function of command Remarks Control commandsBasic format „ Connecting to a PC Cable specifications„ When multiple projectors are connected Example of a control panel layout Using the Remote 2 terminalPin assignments and control Names of terminals Open H Short L Lamp Indication of monitor lamp Procedure of cleaning Cleaning and replacement of air filter Filter to the filter cleaning unit Install the movable metal meshInstall the brush cover so that it Precautions on lamp unit replacement Replacement of lamp unitTiming of lamp unit replacement „ Indication after 1 800 hours Lamp unit to be replaced until Procedure of lamp unit replacementLamp unit cover screw Installation procedure Power does not turn on Symptoms Check point Details Remedy Self-diagnosis display FF0 Model No SpecificationsPT-DW100E RGB2 input Appendix Compatible Signals MAC21 Subwindow List of P in P Outside dimensions Dimensions Index Wired remote control ･･････････････････････････ For business users in the European Union Trademark Acknowledgement