LAN Status, WAN Status, Hardware Status | Patton electronic 2635

Models 2603, 2621, and 2635 Getting Started Guide	12 • System Status

LAN Status

There are two hyperlinks, LAN Settings... and DHCP Server Settings..., which go to the ‘LAN Connections’ and ‘DHCP Server’ webpages, respectively. The other parameters shown in LAN Status are as follows:

•Local IP address: the IP address of the Ethernet port.

•LAN subnet mask: the subnet mask of the Local IP address.

•Act as Local DHCP Server: indicates ‘Yes’ or ‘No’ as to whether the DHCP server is enabled or disabled. An enabled DHCP server provides IP addresses to DHCP clients attached to the Ethernet port.

•MAC address: the MAC address of the Ethernet port.

WAN Status

Displays the basic parameters and status of the WAN port service and a link to the WAN Services conﬁgura- tion web page.

•IP Address Type: indicates whether the IP address of the WAN service is statically assigned or as a DHCP client.

•Default gateway: the gateway deﬁned by the ‘IP Routes’ submenu item under ‘Services Conﬁguration’ in the Conﬁguration Menu.

•Primary DNS: DNS client is currently not available.

Hardware Status

The deﬁnitions of the parameters are as follows.

•Up-Time: this is the time since the IPLink was last rebooted, either soft or hard power cycle.

•Current Time: the time is derived from one of two sources. If the IPLink is conﬁgured as an SNTP client, the time is from an SNTP server. If the SNTP client is not conﬁgured, the time derives from the Clock Set- ting as set by the user. The Clock Setting is found in the ‘SNTP Client’ conﬁguration page.

•Version: lists the version of the operating software in the IPLink. The version information is more detailed than is listed on the Home webpage of the IPLink.

•Set Time...: a link to the SNTP Client conﬁguration page.

Deﬁned Interfaces

Provides links to operating statistics of the deﬁned interfaces.

System Status

110

Image 110

Patton electronic 2635, 2603, 2621 manual LAN Status, WAN Status, Hardware Status, Deﬁned Interfaces

Contents

IPLink Series High Speed Routers Mailsupport@patton.com Summary Table of Contents Contents Contents Models 2603, 2621, and 2635 Getting Started Guide Remote Site Configuration Central site configuration EMC Ethernet Cable 123 Adapter Contents Models 2603, 2621, and 2635 Getting Started Guide List of Figures Models 2603, 2621, and 2635 Getting Started Guide List of Tables Structure About this guideAudience Precautions Impaired functioning Safety when working with electricity General observations General conventions Factory default parametersTypographical conventions used in this document Chapter contents General Information IPLink Series High Speed Routers overview General attributes PPP Support EthernetProtocol support WAN Interfaces Security Front Panel Status LEDs and Console Port Rear panel connectors and switches Console port Power connector Ethernet port outlined in green General Information Product Overview Introduction Applications Overview Sync Serial Application Initial Conﬁguration What you will need Hardware installationInterface cable installation RJ-48C pinout diagram Models 2603, 2621, and 2635 Getting Started Guide Mechanical serviceability Case being opened with a screwdriver Ethernet connector Interface connector RJ-45 DB-25 Installing the AC power cord DCE Initial Configuration Installing the Ethernet cable Do the following PC Conﬁguration IP address modiﬁcationWeb Operation and Conﬁguration Web Browser Model 2603 home Model 2635 home Ethernet LAN Port LAN Connections Ethernet Port Basic Ethernet port attributes Conﬁgurable Ethernet parameters Serial Port Conﬁguration Variables WAN Serial Port ConﬁgurationSerial Interface Web Interface Conﬁguration T1/E1 Interface Conﬁguration Conﬁguring the IPLink Series 2603 for T1 Operation Web Conﬁguration , enter username See ﬁgure Line Options Fractional T1 Conﬁguring the IPLink Series 2603 for E1 Operation Serial Port Configuration WAN Services PPP Bridged WAN Services PPP Bridged WAN Service ConﬁgurationPPP Conﬁguration Leave User name and Password blank. Click on Create PPP Routed Remote site conﬁguration Click on Create Click the Update button PPP link status LMI Management Frame Relay links LMI Conﬁguration Web Conﬁguration Methods Frame Relay Conﬁguration Dlci Number Use Frame Relay bridged Frame Relay bridged creation Central site conﬁguration Frame Relay Routed Relay Description FR routed Frame Relay Channel Routed conﬁguration Cost Interface frame-0 WAN Services Security Click on Create a new service Conﬁguring the router Click on the Create a new Ip route... hyperlink Conﬁguring the security interfaces Valid gateway route Security conﬁguration home Conﬁguring Security Policies Deﬁne ‘ppp-0’ interface as External Deleting a security Policy Enabling the FirewallFirewall Portﬁlters Security Triggers Add Raw IP Filter Conﬁguring TCP port ﬁlter for FTP Adding trigger for FTP data transfer Intrusion Detection System IDS Attack Name Protocol Attacking Host Blacklisted? Security Global address pool and reserved map Introduction to NATEnabling NAT Click on Add Global Address Pool button Dhcp and DNS Conﬁguration Services and features normally associated with each other Dhcp Server NAT Dhcp Server web Parameters for the Dhcp Server subnet Dhcp server conﬁguration web IP Addresses to be available on this subnet Dhcp IP address pool Example based on default range of IP address pool DNS server option information Dhcp Relay Default gateway option informationAdditional option information Conﬁguration of the Dhcp Relay Dhcp Relay webpage DNS Relay Conﬁguring the DNS Relay DNS Relay conﬁguration webpage IP Services CLI Conﬁguration IP ServicesWEB Server Associated Ports for the different System IP Services System Conﬁguration Authentication Authentication web page showing default superuser Alarm Access the conﬁguration and status of the alarms Remote Access Alarm & Alarm Error Log conﬁguration Save UpdateBackup/Restore Website Settings Restart Error Log Snmp Daemon System Tools Snmp Daemon conﬁguration Sntp Client Conﬁguration Sntp Client Mode Conﬁguration Parameters Conﬁguring the Sntp Client System Clock Setting Sntp Client General Conﬁguration Parameters Conﬁguration of the internal system calendar clock System Status System Status Port Connection Status Hardware Status LAN StatusWAN Status Deﬁned Interfaces Status LEDs Contacting Patton for assistance Patton support headquarters in the USA Warranty coverageContact information Return for credit policy Out-of-warranty serviceReturns for credit RMA numbers Appendix a Compliance information EMC Radio and TV Interference FCC Part SafetyCompliance CE Declaration of Conformity Authorized European Representative Appendix B Speciﬁcations Sync Serial Interface General CharacteristicsEthernet T1/E1 Interface Management Protocol SupportPPP Support AC universal power supply DimensionsPower and Power Supply Speciﬁcations VDC power supply Appendix C Cable Recommendations Ethernet Cable Adapter Appendix D IPLink Physical Connectors RJ-45 shielded 10/100 Ethernet port RJ-45 non-shielded RS-232 console port EIA-561 35 M/34 and DB-25 Connector Serial port 21 DB-15 Connector Pin No Circuit Signal Name Direction E1/T1 RJ-48C Connector Pin No Signal Appendix E Command Line Interface CLI Operation Local VT-100 emulation Using the ConsoleCLI Terminology Remote Telnet Then Adding new users Administering user accountsSetting user passwords Controlling user access Changing user settingsControlling login access