Manuals / Patton electronic / Computer Equipment / Network Router

Patton electronic 2621, 2635 WAN Services, Conﬁguring the IPLink Series 2603 for E1 Operation

Models: 2635 2621 2603

1 133

Download 133 pages 54.65 Kb

Page 51

Models 2603, 2621, and 2635 Getting Started Guide	6 • WAN Services

WAN Services

Conﬁguring the IPLink Series 2603 for E1 Operation

Web Conﬁguration. Launch Internet Explorer or similar web browser, type the IP address of the 2603, enter username superuser and password superuser. From the main page click on the T1/E1 > Conﬁguration. (See ﬁgure 26.)

Figure 26. E1 port conﬁguration

Time Slot Select. For unframed E1 service (Clear Channel) go to the “Line Option” parameter and select “Clear Channel E1 (G.703).” For a full framed E1 enter 1-31, for partially ﬁlled E1 enter the range of timeslots using the format for example: 1,2,3,5; or 1-5,10-31. Any entry for timeslots above 31 will return and invalid selection message.

Line Options: Choose from Clear Channel E1(G.703) or Channelized E1(G.703/G.704). Consult with your service provider which option is required.

Line Code: Choose from AMI or HDB3. Most E1 applications use HDB3.

Line Build Out: Select 120 Ohms if the E1 connection is made via the RJ-48C connector, select 75 Ohm if the E1 connection is made via the dual BNC connectors.

FDL Mode: FDL is a T1 application, therefore select ‘Fdl- none’ for E1 applications.

Clocking Mode: Options are Internal or Receive Recover Clock (network). In most applications clocking for the 2603 will be derived from the E1 network, set the unit for Receive Recover unless instructed otherwise by your service provider.

Idle code: Options are Enabled or Disabled. When idle code is Enabled, the 2603 inserts idle codes (7E hex) on unused timeslots. Set this option to Disabled unless instructed otherwise.

Power Down: Options are Normal and Powerdown. When powered down, the E1 will put high impedance on the input and output lines to protect the device—set unit to Normal for regular operation.

WAN Services

51

Image 51

Patton electronic 2621, 2635 manual WAN Services, Conﬁguring the IPLink Series 2603 for E1 Operation

Contents

IPLink Series High Speed Routers Mailsupport@patton.com Summary Table of Contents Contents Contents Models 2603, 2621, and 2635 Getting Started Guide Remote Site Configuration Central site configuration EMC Ethernet Cable 123 Adapter Contents Models 2603, 2621, and 2635 Getting Started Guide List of Figures Models 2603, 2621, and 2635 Getting Started Guide List of Tables About this guide AudienceStructure Impaired functioning Precautions General observations Safety when working with electricity Factory default parameters Typographical conventions used in this documentGeneral conventions General Information Chapter contents General attributes IPLink Series High Speed Routers overview WAN Interfaces EthernetProtocol support PPP Support Front Panel Status LEDs and Console Port Security Console port Rear panel connectors and switches Ethernet port outlined in green Power connector General Information Product Overview Introduction Sync Serial Application Applications Overview Initial Conﬁguration Hardware installation Interface cable installationWhat you will need RJ-48C pinout diagram Models 2603, 2621, and 2635 Getting Started Guide Mechanical serviceability Case being opened with a screwdriver Ethernet connector Interface connector RJ-45 DB-25 DCE Installing the AC power cord Initial Configuration Do the following Installing the Ethernet cable Web Browser IP address modiﬁcationWeb Operation and Conﬁguration PC Conﬁguration Model 2603 home Model 2635 home Ethernet LAN Port Ethernet Port LAN Connections Basic Ethernet port attributes Conﬁgurable Ethernet parameters Serial Port Conﬁguration WAN Serial Port Conﬁguration Serial InterfaceVariables T1/E1 Interface Conﬁguration Web Interface Conﬁguration Web Conﬁguration , enter username See ﬁgure Conﬁguring the IPLink Series 2603 for T1 Operation Conﬁguring the IPLink Series 2603 for E1 Operation Line Options Fractional T1 Serial Port Configuration PPP Bridged WAN Services WAN Services WAN Service Conﬁguration PPP ConﬁgurationPPP Bridged Leave User name and Password blank. Click on Create Remote site conﬁguration PPP Routed Click on Create Click the Update button PPP link status LMI Conﬁguration LMI Management Frame Relay links Web Conﬁguration Methods Dlci Number Use Frame Relay Conﬁguration Frame Relay bridged creation Frame Relay bridged Central site conﬁguration Relay Frame Relay Routed Description FR routed Frame Relay Channel Routed conﬁguration Cost Interface frame-0 WAN Services Security Conﬁguring the router Click on Create a new service Click on the Create a new Ip route... hyperlink Valid gateway route Conﬁguring the security interfaces Security conﬁguration home Deﬁne ‘ppp-0’ interface as External Conﬁguring Security Policies Enabling the Firewall Firewall PortﬁltersDeleting a security Policy Add Raw IP Filter Security Triggers Conﬁguring TCP port ﬁlter for FTP Adding trigger for FTP data transfer Attack Name Protocol Attacking Host Blacklisted? Intrusion Detection System IDS Security Introduction to NAT Enabling NATGlobal address pool and reserved map Click on Add Global Address Pool button Dhcp and DNS Conﬁguration Services and features normally associated with each other NAT Dhcp Server Dhcp Server web Dhcp server conﬁguration web Parameters for the Dhcp Server subnet Dhcp IP address pool IP Addresses to be available on this subnet DNS server option information Example based on default range of IP address pool Conﬁguration of the Dhcp Relay Default gateway option informationAdditional option information Dhcp Relay Dhcp Relay webpage Conﬁguring the DNS Relay DNS Relay DNS Relay conﬁguration webpage IP Services IP Services WEB ServerCLI Conﬁguration Associated Ports for the different System IP Services System Conﬁguration Authentication web page showing default superuser Authentication Access the conﬁguration and status of the alarms Alarm Alarm & Alarm Error Log conﬁguration Remote Access Update Backup/RestoreSave Restart Website Settings Snmp Daemon Error Log Snmp Daemon conﬁguration System Tools Sntp Client Conﬁguration Conﬁguring the Sntp Client Sntp Client Mode Conﬁguration Parameters Sntp Client General Conﬁguration Parameters System Clock Setting Conﬁguration of the internal system calendar clock System Status Port Connection Status System Status Deﬁned Interfaces LAN StatusWAN Status Hardware Status Status LEDs Contacting Patton for assistance Warranty coverage Contact informationPatton support headquarters in the USA RMA numbers Out-of-warranty serviceReturns for credit Return for credit policy EMC Appendix a Compliance information CE Declaration of Conformity SafetyCompliance Radio and TV Interference FCC Part Authorized European Representative Appendix B Speciﬁcations T1/E1 Interface General CharacteristicsEthernet Sync Serial Interface Protocol Support PPP SupportManagement VDC power supply DimensionsPower and Power Supply Speciﬁcations AC universal power supply Appendix C Cable Recommendations Adapter Ethernet Cable Appendix D IPLink Physical Connectors RJ-45 non-shielded RS-232 console port EIA-561 RJ-45 shielded 10/100 Ethernet port Serial port 35 M/34 and DB-25 Connector Pin No Circuit Signal Name Direction 21 DB-15 Connector Pin No Signal E1/T1 RJ-48C Connector Appendix E Command Line Interface CLI Operation Remote Telnet Using the ConsoleCLI Terminology Local VT-100 emulation Then Administering user accounts Setting user passwordsAdding new users Changing user settings Controlling login accessControlling user access