Installing the Ethernet cable | Patton electronic 2603, 2621, 2635

Models 2603, 2621, and 2635 Getting Started Guide	3 • Initial Configuration

Power

		Gateway
	ipLink	Router
2603
WAN
ModelSpeed	Console
High	Console

				100M	Rx
			Link	Tx
	Frame	RD	Link
	Frame	RD	Ethernet
Link	TD
	WAN

Model 2603 ipLink Gateway

High Speed WAN Access Router

Power	Link FrameTD RD
	WAN

Link 100MTx Rx

Ethernet

Console

	Power	WAN Link WAN TD		Ethernet	Ethernet Tx	Ethernet Rx	Console
	LED
		LED	LED	Link	LED	LED	port

		WAN Frame	WAN RD LED		Ethernet
		LED	LED		100M
					LED

Figure 13. IPLink front panel LEDs and Console port locations (Model 2603 shown)

Installing the Ethernet cable

Do the following:

The interconnecting cables shall be acceptable for external use and shall be rated for the proper application with respect to volt- age, current, anticipated temperature, ﬂammability, and

CAUTION mechanical serviceability.

1.Connect the DB9-RJ45 adapter to the DB-9 serial port on the PC or dumb terminal. Use the RJ45-RJ45 straight-through cable between the adapter and the red marked RJ45 port on the IPLink Router.

2.Do not connect the router to the Ethernet LAN at this time.

3.On the PC, start a terminal emulation session (such as TeraTerm or HyperTerminal) at 9600 bps, 8 data bits, 1 stop bit, and no parity.

4.Plug the AC power cord into The IPLink Series router to power up the router.

5.Type superuser for Login:, and press Enter.

6.Then type superuser for the password, press Enter.

Hardware installation

36

Image 36

Patton electronic 2603, 2621, 2635 manual Installing the Ethernet cable, Do the following

Contents

IPLink Series High Speed Routers Mailsupport@patton.com Summary Table of Contents Contents Contents Models 2603, 2621, and 2635 Getting Started Guide Remote Site Configuration Central site configuration EMC Ethernet Cable 123 Adapter Contents Models 2603, 2621, and 2635 Getting Started Guide List of Figures Models 2603, 2621, and 2635 Getting Started Guide List of Tables About this guide AudienceStructure Precautions Impaired functioning Safety when working with electricity General observations Factory default parameters Typographical conventions used in this documentGeneral conventions Chapter contents General Information IPLink Series High Speed Routers overview General attributes Ethernet Protocol supportPPP Support WAN Interfaces Security Front Panel Status LEDs and Console Port Rear panel connectors and switches Console port Power connector Ethernet port outlined in green General Information Product Overview Introduction Applications Overview Sync Serial Application Initial Conﬁguration Hardware installation Interface cable installationWhat you will need RJ-48C pinout diagram Models 2603, 2621, and 2635 Getting Started Guide Mechanical serviceability Case being opened with a screwdriver Ethernet connector Interface connector RJ-45 DB-25 Installing the AC power cord DCE Initial Configuration Installing the Ethernet cable Do the following IP address modiﬁcation Web Operation and ConﬁgurationPC Conﬁguration Web Browser Model 2603 home Model 2635 home Ethernet LAN Port LAN Connections Ethernet Port Basic Ethernet port attributes Conﬁgurable Ethernet parameters Serial Port Conﬁguration WAN Serial Port Conﬁguration Serial InterfaceVariables Web Interface Conﬁguration T1/E1 Interface Conﬁguration Conﬁguring the IPLink Series 2603 for T1 Operation Web Conﬁguration , enter username See ﬁgure Line Options Fractional T1 Conﬁguring the IPLink Series 2603 for E1 Operation Serial Port Configuration WAN Services PPP Bridged WAN Services WAN Service Conﬁguration PPP ConﬁgurationPPP Bridged Leave User name and Password blank. Click on Create PPP Routed Remote site conﬁguration Click on Create Click the Update button PPP link status LMI Management Frame Relay links LMI Conﬁguration Web Conﬁguration Methods Frame Relay Conﬁguration Dlci Number Use Frame Relay bridged Frame Relay bridged creation Central site conﬁguration Frame Relay Routed Relay Description FR routed Frame Relay Channel Routed conﬁguration Cost Interface frame-0 WAN Services Security Click on Create a new service Conﬁguring the router Click on the Create a new Ip route... hyperlink Conﬁguring the security interfaces Valid gateway route Security conﬁguration home Conﬁguring Security Policies Deﬁne ‘ppp-0’ interface as External Enabling the Firewall Firewall PortﬁltersDeleting a security Policy Security Triggers Add Raw IP Filter Conﬁguring TCP port ﬁlter for FTP Adding trigger for FTP data transfer Intrusion Detection System IDS Attack Name Protocol Attacking Host Blacklisted? Security Introduction to NAT Enabling NATGlobal address pool and reserved map Click on Add Global Address Pool button Dhcp and DNS Conﬁguration Services and features normally associated with each other Dhcp Server NAT Dhcp Server web Parameters for the Dhcp Server subnet Dhcp server conﬁguration web IP Addresses to be available on this subnet Dhcp IP address pool Example based on default range of IP address pool DNS server option information Default gateway option information Additional option informationDhcp Relay Conﬁguration of the Dhcp Relay Dhcp Relay webpage DNS Relay Conﬁguring the DNS Relay DNS Relay conﬁguration webpage IP Services IP Services WEB ServerCLI Conﬁguration Associated Ports for the different System IP Services System Conﬁguration Authentication Authentication web page showing default superuser Alarm Access the conﬁguration and status of the alarms Remote Access Alarm & Alarm Error Log conﬁguration Update Backup/RestoreSave Website Settings Restart Error Log Snmp Daemon System Tools Snmp Daemon conﬁguration Sntp Client Conﬁguration Sntp Client Mode Conﬁguration Parameters Conﬁguring the Sntp Client System Clock Setting Sntp Client General Conﬁguration Parameters Conﬁguration of the internal system calendar clock System Status System Status Port Connection Status LAN Status WAN StatusHardware Status Deﬁned Interfaces Status LEDs Contacting Patton for assistance Warranty coverage Contact informationPatton support headquarters in the USA Out-of-warranty service Returns for creditReturn for credit policy RMA numbers Appendix a Compliance information EMC Safety ComplianceRadio and TV Interference FCC Part CE Declaration of Conformity Authorized European Representative Appendix B Speciﬁcations General Characteristics EthernetSync Serial Interface T1/E1 Interface Protocol Support PPP SupportManagement Dimensions Power and Power Supply SpeciﬁcationsAC universal power supply VDC power supply Appendix C Cable Recommendations Ethernet Cable Adapter Appendix D IPLink Physical Connectors RJ-45 shielded 10/100 Ethernet port RJ-45 non-shielded RS-232 console port EIA-561 35 M/34 and DB-25 Connector Serial port 21 DB-15 Connector Pin No Circuit Signal Name Direction E1/T1 RJ-48C Connector Pin No Signal Appendix E Command Line Interface CLI Operation Using the Console CLI TerminologyLocal VT-100 emulation Remote Telnet Then Administering user accounts Setting user passwordsAdding new users Changing user settings Controlling login accessControlling user access