About this guide, Audience, Structure | Patton electronic 2621

About this guide

This guide describes installing and conﬁguring Patton Electronics IPLink Series High Speed Routers. The instructions in this guide are based on the following assumptions:

•The router may connect to a serial DTE device or T1/E1 line

•There is a LAN connected to the Ethernet port of the router

Audience

This guide is intended for the following users:

•Operators

•Installers

•Maintenance technicians

Structure

This guide contains the following chapters and appendices:

•Chapter 1 on page 17 provides information about router features and capabilities

•Chapter 2 on page 24 contains an overview describing router operation

•Chapter 3 on page 27 provides initial conﬁguration procedures

•Chapter 4 on page 40 describes conﬁguring the Ethernet LAN interface

•Chapter 5 on page 44 describes conﬁguring the serial WAN interfaces

•Chapter 6 on page 50 describes conﬁguring WAN services

•Chapter 7 on page 68 describes conﬁguring security for the router

•Chapter 8 on page 82 describes DHCP and DNS conﬁguration

•Chapter 9 on page 93 describes conﬁguring IP services

•Chapter 10 on page 96 describes system conﬁguration

•Chapter 11 on page 104 describes SNTP client conﬁguration

•Chapter 12 on page 108 provides a summary of the IPLink’s status webpage and status LEDs

•Chapter 13 on page 112contains information on contacting Patton technical support for assistance

•Appendix A on page 115 contains compliance information for the IPLink routers

•Appendix B on page 118 contains speciﬁcations for the routers

•Appendix C on page 122 provides cable recommendations

•Appendix D on page 124 describes the router’s ports

•Appendix E on page 129 describes how to use the command line interface (CLI)

For best results, read the contents of this guide before you install the router.

13

Image 13

Patton electronic 2621, 2603, 2635 manual About this guide, Audience, Structure

Contents

IPLink Series High Speed Routers Mailsupport@patton.com Summary Table of Contents Contents Contents Models 2603, 2621, and 2635 Getting Started Guide Remote Site Configuration Central site configuration EMC Ethernet Cable 123 Adapter Contents Models 2603, 2621, and 2635 Getting Started Guide List of Figures Models 2603, 2621, and 2635 Getting Started Guide List of Tables Audience About this guideStructure Impaired functioning Precautions General observations Safety when working with electricity Typographical conventions used in this document Factory default parametersGeneral conventions General Information Chapter contents General attributes IPLink Series High Speed Routers overview Protocol support EthernetPPP Support WAN Interfaces Front Panel Status LEDs and Console Port Security Console port Rear panel connectors and switches Ethernet port outlined in green Power connector General Information Product Overview Introduction Sync Serial Application Applications Overview Initial Conﬁguration Interface cable installation Hardware installationWhat you will need RJ-48C pinout diagram Models 2603, 2621, and 2635 Getting Started Guide Mechanical serviceability Case being opened with a screwdriver Ethernet connector Interface connector RJ-45 DB-25 DCE Installing the AC power cord Initial Configuration Do the following Installing the Ethernet cable Web Operation and Conﬁguration IP address modiﬁcationPC Conﬁguration Web Browser Model 2603 home Model 2635 home Ethernet LAN Port Ethernet Port LAN Connections Basic Ethernet port attributes Conﬁgurable Ethernet parameters Serial Port Conﬁguration Serial Interface WAN Serial Port ConﬁgurationVariables T1/E1 Interface Conﬁguration Web Interface Conﬁguration Web Conﬁguration , enter username See ﬁgure Conﬁguring the IPLink Series 2603 for T1 Operation Conﬁguring the IPLink Series 2603 for E1 Operation Line Options Fractional T1 Serial Port Configuration PPP Bridged WAN Services WAN Services PPP Conﬁguration WAN Service ConﬁgurationPPP Bridged Leave User name and Password blank. Click on Create Remote site conﬁguration PPP Routed Click on Create Click the Update button PPP link status LMI Conﬁguration LMI Management Frame Relay links Web Conﬁguration Methods Dlci Number Use Frame Relay Conﬁguration Frame Relay bridged creation Frame Relay bridged Central site conﬁguration Relay Frame Relay Routed Description FR routed Frame Relay Channel Routed conﬁguration Cost Interface frame-0 WAN Services Security Conﬁguring the router Click on Create a new service Click on the Create a new Ip route... hyperlink Valid gateway route Conﬁguring the security interfaces Security conﬁguration home Deﬁne ‘ppp-0’ interface as External Conﬁguring Security Policies Firewall Portﬁlters Enabling the FirewallDeleting a security Policy Add Raw IP Filter Security Triggers Conﬁguring TCP port ﬁlter for FTP Adding trigger for FTP data transfer Attack Name Protocol Attacking Host Blacklisted? Intrusion Detection System IDS Security Enabling NAT Introduction to NATGlobal address pool and reserved map Click on Add Global Address Pool button Dhcp and DNS Conﬁguration Services and features normally associated with each other NAT Dhcp Server Dhcp Server web Dhcp server conﬁguration web Parameters for the Dhcp Server subnet Dhcp IP address pool IP Addresses to be available on this subnet DNS server option information Example based on default range of IP address pool Additional option information Default gateway option informationDhcp Relay Conﬁguration of the Dhcp Relay Dhcp Relay webpage Conﬁguring the DNS Relay DNS Relay DNS Relay conﬁguration webpage IP Services WEB Server IP ServicesCLI Conﬁguration Associated Ports for the different System IP Services System Conﬁguration Authentication web page showing default superuser Authentication Access the conﬁguration and status of the alarms Alarm Alarm & Alarm Error Log conﬁguration Remote Access Backup/Restore UpdateSave Restart Website Settings Snmp Daemon Error Log Snmp Daemon conﬁguration System Tools Sntp Client Conﬁguration Conﬁguring the Sntp Client Sntp Client Mode Conﬁguration Parameters Sntp Client General Conﬁguration Parameters System Clock Setting Conﬁguration of the internal system calendar clock System Status Port Connection Status System Status WAN Status LAN StatusHardware Status Deﬁned Interfaces Status LEDs Contacting Patton for assistance Contact information Warranty coveragePatton support headquarters in the USA Returns for credit Out-of-warranty serviceReturn for credit policy RMA numbers EMC Appendix a Compliance information Compliance SafetyRadio and TV Interference FCC Part CE Declaration of Conformity Authorized European Representative Appendix B Speciﬁcations Ethernet General CharacteristicsSync Serial Interface T1/E1 Interface PPP Support Protocol SupportManagement Power and Power Supply Speciﬁcations DimensionsAC universal power supply VDC power supply Appendix C Cable Recommendations Adapter Ethernet Cable Appendix D IPLink Physical Connectors RJ-45 non-shielded RS-232 console port EIA-561 RJ-45 shielded 10/100 Ethernet port Serial port 35 M/34 and DB-25 Connector Pin No Circuit Signal Name Direction 21 DB-15 Connector Pin No Signal E1/T1 RJ-48C Connector Appendix E Command Line Interface CLI Operation CLI Terminology Using the ConsoleLocal VT-100 emulation Remote Telnet Then Setting user passwords Administering user accountsAdding new users Controlling login access Changing user settingsControlling user access