Manuals / Paxar / Computer Equipment / Printer

Paxar Monarch 9476 manual Attach the Drop Shelf, 1-10, Assembly and Setup Instructions

Models: Monarch 9476

1 64

Download 64 pages 62.61 Kb

Page 16

Image 16

9476 Assembly and Setup Instructions

Attach the Drop Shelf

1.Remove the following items from their packaging: F (1) support brace

F (1) metal rod F (1) drop shelf F (2) end caps

F (2) 1/4"-20 x 1/2" phillips screws F (2) plastic washers

2.Attach the support brace to the Station’s corner supports on either the front or the rear of the Station using two 1/2" phillips screws. The open side of the support brace must face down. (Figure 6.)

Support

Brace

Corner

Support

Figure 6

nDo not tighten the screws completely.

1-10

Page 16

Image 16

Paxar Monarch 9476 manual Attach the Drop Shelf, 1-10, Assembly and Setup Instructions

Contents

Assembly and Setup Instructions MonarchTM 9476TM Mobile Printing StationTC9476OI Rev. AA 4/99 1995 Monarch Marking Systems, Inc. All rights reservedCANADIAN D.O.C. WARNING Monarch Marking Systems P.O. Box Dayton, OhioPreface Audience9476 Assembly and Setup Instructions Other DocumentationMPCLII Packet Reference Manual Addressing a MonarchTable of Contents 9476 Assembly and Setup Instructions Chapter 4. TroubleshootingSolving Problems Changing Fuses Changing the Battery Fuse Chapter 5. SpecificationsChapter 1. Assembling the Station Parts ListGeneral Cart Packaging Battery and Charger Packaging 9476 Assembly and Setup InstructionsTools You Need Step 1 Attaching the Wheels and CastersChapter 1. Assembling the Station 9476 Assembly and Setup Instructions Washer Axle Mount Washer end cap Wheel AxleChapter 1. Assembling the Station Axle Caster Mount SocketStep 2 Adjusting the Station’s Height 9476 Assembly and Setup InstructionsStep 3 Attaching the Cabinet Handle and Cord Bracket Chapter 1. Assembling the Station9476 Assembly and Setup Instructions Step 4 Attaching Optional ItemsCord Bracket Handle Insert Attach the Push Handle Chapter 1. Assembling the Station1. Remove the following items from their packaging F 1 push handle F 4 1/4-20 x 3/4 hex bolts F 4 1/4-20 nuts F 4 1/4-20 washers1-10 Attach the Drop Shelf9476 Assembly and Setup Instructions Chapter 1. Assembling the Station 1-114. Finish tightening the screws to secure the support brace 9476 Assembly and Setup Instructions 1-129. Slide the metal rod through the slot in the side of the drop shelf and into the hole in the Station’s corner support. Push the rod until it exits through the hole in the other corner support. You may have to reach under the support brace to guide the rod into the opposite hole. Figure Attach the Data Entry Terminal Cradle 1-13Chapter 1. Assembling the Station Terminal Cradle MagnetStep 5 Installing the Battery and Charger Install the Battery1-14 9476 Assembly and Setup InstructionsChapter 1. Assembling the Station 1-15Retainer Rod 9476 Assembly and Setup Instructions 1-164. Slide the battery to the back of the cabinet Rubber Bracket Retainer Rod Ground Wire 1-17Chapter 1. Assembling the Station Install the Battery Charger 1-189476 Assembly and Setup Instructions F 2 metal retainer rods F 1 rubber bracketChapter 1. Assembling the Station 1-19Retainer Rod 9476 Assembly and Setup Instructions 1-206. Place the charger on the cabinet floor Rubber Bracket Retainer Rod External Power Socket 1-21Chapter 1. Assembling the Station Step 6 Installing the Printers Attach the Printer Brackets1-22 9476 Assembly and Setup Instructions1-23 Attach the PrintersChapter 1. Assembling the Station 1-24 9476 Assembly and Setup InstructionsPower Pack Battery Well Shoulder Screw1-25 Chapter 1. Assembling the StationShoulder Screw Printer Bracket Fan-fold9476 Assembly and Setup Instructions 1-26Printer Port Cable Chapter Loading Supplies9476 Assembly and Setup Instructions Printhead Assembly Platen Roller Pinch Rollers Peel Bar2. Pull the supply guide forward and down as shown. Figure Supply GuideLoading Fan-Fold Supplies Chapter 2. Loading Supplies9476 Assembly and Setup Instructions 4. Roll the O-rings out of their tracks and into the new positionsChapter 2. Loading Supplies Supply Strip Fan-Fold Slot Magnetic Supply Bracket9476 Assembly and Setup Instructions 9. Feed the supply’s leading edge into the printer’s fan-fold slot. The black mark on the supply must be facing up if it is not, flip the supply stack over. Make sure the arrow printed on the back of the supply points toward the printer. Center the supply in the printer by lining up the black mark within the centering notch. FigureChapter 2. Loading Supplies Supply Deflector9476 Assembly and Setup Instructions Supply Guide Upper OpeningLoading Roll Supplies in Fan-Fold Printers Chapter 2. Loading Supplies9476 Assembly and Setup Instructions 2-10Supply Holder Arrow Width of Supply Tabs 2-11 Chapter 2. Loading SuppliesnMake sure the supplies turn freely in the supply well Supply Holder9476 Assembly and Setup Instructions 2-12Supply Guide Upper Opening Chapter 2. Loading Supplies 2-13Supply Guide Upper Opening Lower Opening Loading Ribbon 2-149476 Assembly and Setup Instructions Use ribbon when printing on thermal transfer supplies2-15 Reloading a Ribbon CassetteChapter 2. Loading Supplies 9476 Assembly and Setup Instructions 2-16nDo Not wrinkle or crush the ribbon Printing 2-17Power Switch Chapter 2. Loading Supplies9476 Assembly and Setup Instructions 2-183. Turn each printer on and press each printer’s trigger to calibrate the supply. You are now ready to collect data and print Chapter 3. Charging the Battery Important Charging Information 9476 Assembly and Setup InstructionsBattery Life Chapter 3. Charging the Battery9476 Assembly and Setup Instructions 3-4 Solving Problems TroubleshootingChapter Changing Fuses Changing the Battery Fuse9476 Assembly and Setup Instructions Chapter 4. Troubleshooting 2. Open the Station’s cabinet. as shown until it pops outPress and turn the fuse cover Figure 3. Pull the fuse out of the cover. FigureChanging the AC Fuse 9476 Assembly and Setup InstructionsChapter 4. Troubleshooting 7. Plug the power cord back into the power socket on the Station4. Slide the fuse holder out and remove the fuse. Figure 6. Push the fuse holder until it snaps back into place. Figure9476 Assembly and Setup Instructions Specifications BatteryWeight Utility CartCharger InputOutput 9476 Assembly and Setup InstructionsPage For supplies, service, or assistance call TOLL FREEPublished by the Technical Communications Department Printed in the U.S.A