Manuals / Paxar / Computer Equipment / Printer

Paxar Monarch 9476 manual Attaching the Cabinet Handle and Cord Bracket, Assembling the Station

Models: Monarch 9476

1 64

Download 64 pages 62.61 Kb

Page 13

Image 13

Chapter 1. Assembling the Station

nDo Not set the top shelf to the highest adjustment.

5.Attach the plastic cable-tube clamp around the bottom of the cable tube as shown (if it is not already attached). Squeeze the finger grips to lock the clamp around the cable tube. Use pliers to secure the cable clamp tightly. (Figure 3.)

Step 3: Attaching the Cabinet Handle and Cord Bracket ------------------

Follow the steps below to install the cabinet handle and cord bracket.

1.Remove the following items from their packaging: F chrome handle insert

F two 5/8" phillips screws (black) F cord bracket

F two 8-32 x 1/2" slotted screws (black) F two 8-32 nuts/lockwashers (black)

1-7

Page 13

Image 13

Paxar Monarch 9476 manual Attaching the Cabinet Handle and Cord Bracket, Assembling the Station

Contents

MonarchTM 9476TM Mobile Printing Station Assembly and Setup InstructionsTC9476OI Rev. AA 4/99 1995 Monarch Marking Systems, Inc. All rights reservedMonarch Marking Systems P.O. Box Dayton, Ohio CANADIAN D.O.C. WARNINGAudience PrefaceOther Documentation 9476 Assembly and Setup InstructionsMPCLII Packet Reference Manual Addressing a MonarchTable of Contents Chapter 4. Troubleshooting 9476 Assembly and Setup InstructionsSolving Problems Changing Fuses Changing the Battery Fuse Chapter 5. SpecificationsChapter 1. Assembling the Station Parts ListGeneral Cart Packaging 9476 Assembly and Setup Instructions Battery and Charger PackagingTools You Need Step 1 Attaching the Wheels and CastersChapter 1. Assembling the Station Washer Axle Mount Washer end cap Wheel Axle 9476 Assembly and Setup InstructionsAxle Caster Mount Socket Chapter 1. Assembling the Station9476 Assembly and Setup Instructions Step 2 Adjusting the Station’s HeightChapter 1. Assembling the Station Step 3 Attaching the Cabinet Handle and Cord Bracket9476 Assembly and Setup Instructions Step 4 Attaching Optional ItemsCord Bracket Handle Insert Chapter 1. Assembling the Station Attach the Push Handle1. Remove the following items from their packaging F 1 push handle F 4 1/4-20 x 3/4 hex bolts F 4 1/4-20 nuts F 4 1/4-20 washers1-10 Attach the Drop Shelf9476 Assembly and Setup Instructions Chapter 1. Assembling the Station 1-114. Finish tightening the screws to secure the support brace 9476 Assembly and Setup Instructions 1-129. Slide the metal rod through the slot in the side of the drop shelf and into the hole in the Station’s corner support. Push the rod until it exits through the hole in the other corner support. You may have to reach under the support brace to guide the rod into the opposite hole. Figure 1-13 Attach the Data Entry Terminal CradleChapter 1. Assembling the Station Terminal Cradle MagnetInstall the Battery Step 5 Installing the Battery and Charger1-14 9476 Assembly and Setup InstructionsChapter 1. Assembling the Station 1-15Retainer Rod 9476 Assembly and Setup Instructions 1-164. Slide the battery to the back of the cabinet Rubber Bracket Retainer Rod Ground Wire 1-17Chapter 1. Assembling the Station 1-18 Install the Battery Charger9476 Assembly and Setup Instructions F 2 metal retainer rods F 1 rubber bracketChapter 1. Assembling the Station 1-19Retainer Rod 9476 Assembly and Setup Instructions 1-206. Place the charger on the cabinet floor Rubber Bracket Retainer Rod External Power Socket 1-21Chapter 1. Assembling the Station Attach the Printer Brackets Step 6 Installing the Printers1-22 9476 Assembly and Setup Instructions1-23 Attach the PrintersChapter 1. Assembling the Station 9476 Assembly and Setup Instructions 1-24Power Pack Battery Well Shoulder ScrewChapter 1. Assembling the Station 1-25Shoulder Screw Printer Bracket Fan-fold9476 Assembly and Setup Instructions 1-26Printer Port Cable Loading Supplies ChapterPrinthead Assembly Platen Roller Pinch Rollers Peel Bar 9476 Assembly and Setup Instructions2. Pull the supply guide forward and down as shown. Figure Supply GuideChapter 2. Loading Supplies Loading Fan-Fold Supplies4. Roll the O-rings out of their tracks and into the new positions 9476 Assembly and Setup InstructionsSupply Strip Fan-Fold Slot Magnetic Supply Bracket Chapter 2. Loading Supplies9. Feed the supply’s leading edge into the printer’s fan-fold slot. The black mark on the supply must be facing up if it is not, flip the supply stack over. Make sure the arrow printed on the back of the supply points toward the printer. Center the supply in the printer by lining up the black mark within the centering notch. Figure 9476 Assembly and Setup InstructionsSupply Deflector Chapter 2. Loading SuppliesSupply Guide Upper Opening 9476 Assembly and Setup InstructionsChapter 2. Loading Supplies Loading Roll Supplies in Fan-Fold Printers9476 Assembly and Setup Instructions 2-10Supply Holder Arrow Width of Supply Tabs Chapter 2. Loading Supplies 2-11nMake sure the supplies turn freely in the supply well Supply Holder9476 Assembly and Setup Instructions 2-12Supply Guide Upper Opening Chapter 2. Loading Supplies 2-13Supply Guide Upper Opening Lower Opening 2-14 Loading Ribbon9476 Assembly and Setup Instructions Use ribbon when printing on thermal transfer supplies2-15 Reloading a Ribbon CassetteChapter 2. Loading Supplies 9476 Assembly and Setup Instructions 2-16nDo Not wrinkle or crush the ribbon 2-17 PrintingPower Switch Chapter 2. Loading Supplies9476 Assembly and Setup Instructions 2-183. Turn each printer on and press each printer’s trigger to calibrate the supply. You are now ready to collect data and print Chapter 3. Charging the Battery 9476 Assembly and Setup Instructions Important Charging InformationChapter 3. Charging the Battery Battery Life9476 Assembly and Setup Instructions 3-4 Solving Problems TroubleshootingChapter Changing Fuses Changing the Battery Fuse9476 Assembly and Setup Instructions 2. Open the Station’s cabinet. as shown until it pops out Chapter 4. TroubleshootingPress and turn the fuse cover Figure 3. Pull the fuse out of the cover. Figure9476 Assembly and Setup Instructions Changing the AC Fuse7. Plug the power cord back into the power socket on the Station Chapter 4. Troubleshooting4. Slide the fuse holder out and remove the fuse. Figure 6. Push the fuse holder until it snaps back into place. Figure9476 Assembly and Setup Instructions Battery SpecificationsWeight Utility CartInput ChargerOutput 9476 Assembly and Setup InstructionsPage TOLL FREE For supplies, service, or assistance callPublished by the Technical Communications Department Printed in the U.S.A