Manuals / Paxar / Computer Equipment / Printer

Paxar Monarch 9476 manual Installing the Battery and Charger, Install the Battery, 1-14

Models: Monarch 9476

1 64

Download 64 pages 62.61 Kb

Page 20

Image 20

9476 Assembly and Setup Instructions

Step 5: Installing the Battery and Charger ------------------------------------------

Follow the steps below to install the battery and battery charger.

Install the Battery

Only qualified service personnel may install or replace the battery.

1.Remove the following items from their packaging: F (1) 12-volt battery

F (2) metal retainer rods F (2) 1/4"-20 wing nuts F (1) rubber bracket

F (1) green wire

F (1) M5 x 10mm phillips screw

F (2) M5 x 15mm phillips/hex bolts F (3) M5 nuts

F (2) 1/4"-20 washers

F (2) 1/4"-20 lockwashers F (2) M5 washers

F (3) M5 lockwashers

1-14

Page 20

Image 20

Paxar Monarch 9476 manual Installing the Battery and Charger, Install the Battery, 1-14, Assembly and Setup Instructions

Contents

Assembly and Setup Instructions MonarchTM 9476TM Mobile Printing StationTC9476OI Rev. AA 4/99 1995 Monarch Marking Systems, Inc. All rights reservedCANADIAN D.O.C. WARNING Monarch Marking Systems P.O. Box Dayton, OhioPreface Audience9476 Assembly and Setup Instructions Other DocumentationMPCLII Packet Reference Manual Addressing a MonarchTable of Contents 9476 Assembly and Setup Instructions Chapter 4. TroubleshootingSolving Problems Changing Fuses Changing the Battery Fuse Chapter 5. SpecificationsGeneral Cart Packaging Parts ListChapter 1. Assembling the Station Battery and Charger Packaging 9476 Assembly and Setup InstructionsChapter 1. Assembling the Station Step 1 Attaching the Wheels and CastersTools You Need 9476 Assembly and Setup Instructions Washer Axle Mount Washer end cap Wheel AxleChapter 1. Assembling the Station Axle Caster Mount SocketStep 2 Adjusting the Station’s Height 9476 Assembly and Setup InstructionsStep 3 Attaching the Cabinet Handle and Cord Bracket Chapter 1. Assembling the StationCord Bracket Handle Insert Step 4 Attaching Optional Items9476 Assembly and Setup Instructions Attach the Push Handle Chapter 1. Assembling the Station1. Remove the following items from their packaging F 1 push handle F 4 1/4-20 x 3/4 hex bolts F 4 1/4-20 nuts F 4 1/4-20 washers9476 Assembly and Setup Instructions Attach the Drop Shelf1-10 4. Finish tightening the screws to secure the support brace 1-11Chapter 1. Assembling the Station 9. Slide the metal rod through the slot in the side of the drop shelf and into the hole in the Station’s corner support. Push the rod until it exits through the hole in the other corner support. You may have to reach under the support brace to guide the rod into the opposite hole. Figure 1-129476 Assembly and Setup Instructions Attach the Data Entry Terminal Cradle 1-13Chapter 1. Assembling the Station Terminal Cradle MagnetStep 5 Installing the Battery and Charger Install the Battery1-14 9476 Assembly and Setup InstructionsRetainer Rod 1-15Chapter 1. Assembling the Station 4. Slide the battery to the back of the cabinet 1-169476 Assembly and Setup Instructions Chapter 1. Assembling the Station 1-17Rubber Bracket Retainer Rod Ground Wire Install the Battery Charger 1-189476 Assembly and Setup Instructions F 2 metal retainer rods F 1 rubber bracketRetainer Rod 1-19Chapter 1. Assembling the Station 6. Place the charger on the cabinet floor 1-209476 Assembly and Setup Instructions Chapter 1. Assembling the Station 1-21Rubber Bracket Retainer Rod External Power Socket Step 6 Installing the Printers Attach the Printer Brackets1-22 9476 Assembly and Setup InstructionsChapter 1. Assembling the Station Attach the Printers1-23 1-24 9476 Assembly and Setup InstructionsPower Pack Battery Well Shoulder Screw1-25 Chapter 1. Assembling the StationShoulder Screw Printer Bracket Fan-foldPrinter Port Cable 1-269476 Assembly and Setup Instructions Chapter Loading Supplies9476 Assembly and Setup Instructions Printhead Assembly Platen Roller Pinch Rollers Peel Bar2. Pull the supply guide forward and down as shown. Figure Supply GuideLoading Fan-Fold Supplies Chapter 2. Loading Supplies9476 Assembly and Setup Instructions 4. Roll the O-rings out of their tracks and into the new positionsChapter 2. Loading Supplies Supply Strip Fan-Fold Slot Magnetic Supply Bracket9476 Assembly and Setup Instructions 9. Feed the supply’s leading edge into the printer’s fan-fold slot. The black mark on the supply must be facing up if it is not, flip the supply stack over. Make sure the arrow printed on the back of the supply points toward the printer. Center the supply in the printer by lining up the black mark within the centering notch. FigureChapter 2. Loading Supplies Supply Deflector9476 Assembly and Setup Instructions Supply Guide Upper OpeningLoading Roll Supplies in Fan-Fold Printers Chapter 2. Loading SuppliesSupply Holder Arrow Width of Supply Tabs 2-109476 Assembly and Setup Instructions 2-11 Chapter 2. Loading SuppliesnMake sure the supplies turn freely in the supply well Supply HolderSupply Guide Upper Opening 2-129476 Assembly and Setup Instructions Supply Guide Upper Opening Lower Opening 2-13Chapter 2. Loading Supplies Loading Ribbon 2-149476 Assembly and Setup Instructions Use ribbon when printing on thermal transfer suppliesChapter 2. Loading Supplies Reloading a Ribbon Cassette2-15 nDo Not wrinkle or crush the ribbon 2-169476 Assembly and Setup Instructions Printing 2-17Power Switch Chapter 2. Loading Supplies3. Turn each printer on and press each printer’s trigger to calibrate the supply. You are now ready to collect data and print 2-189476 Assembly and Setup Instructions Chapter 3. Charging the Battery Important Charging Information 9476 Assembly and Setup InstructionsBattery Life Chapter 3. Charging the Battery9476 Assembly and Setup Instructions 3-4 Chapter TroubleshootingSolving Problems 9476 Assembly and Setup Instructions Changing the Battery FuseChanging Fuses Chapter 4. Troubleshooting 2. Open the Station’s cabinet. as shown until it pops outPress and turn the fuse cover Figure 3. Pull the fuse out of the cover. FigureChanging the AC Fuse 9476 Assembly and Setup InstructionsChapter 4. Troubleshooting 7. Plug the power cord back into the power socket on the Station4. Slide the fuse holder out and remove the fuse. Figure 6. Push the fuse holder until it snaps back into place. Figure9476 Assembly and Setup Instructions Specifications BatteryWeight Utility CartCharger InputOutput 9476 Assembly and Setup InstructionsPage For supplies, service, or assistance call TOLL FREEPublished by the Technical Communications Department Printed in the U.S.A