Manuals / Paxar / Computer Equipment / Printer

Paxar Monarch 9476 manual Loading Fan-Fold Supplies, Loading Supplies

Models: Monarch 9476

1 64

Download 64 pages 62.61 Kb

Page 35

Chapter 2. Loading Supplies

Chapter 2. Loading Supplies

4.Slide the latches on the back of the printer toward the center. (Figure 24.)

5.Continue to push the printhead assembly toward the rear of the printer until it opens completely.

Latches

Figure 24

Loading Fan-Fold Supplies ----------------------------------------------------------------------

To load fan-fold supplies into your printer, follow the steps below.

nWhen using fan-fold labels, load for non-peel mode only. Non-peel mode feeds the labels through the printer without peeling them from the backing paper. The printer does not print fan-fold labels in peel mode.

1.Open the printer.

2-3

Image 35

Paxar Monarch 9476 manual Loading Fan-Fold Supplies, Loading Supplies

Contents

1995 Monarch Marking Systems, Inc. All rights reserved Assembly and Setup InstructionsMonarchTM 9476TM Mobile Printing Station TC9476OI Rev. AA 4/99Monarch Marking Systems P.O. Box Dayton, Ohio CANADIAN D.O.C. WARNINGAudience PrefaceAddressing a Monarch 9476 Assembly and Setup InstructionsOther Documentation MPCLII Packet Reference ManualTable of Contents Chapter 5. Specifications 9476 Assembly and Setup InstructionsChapter 4. Troubleshooting Solving Problems Changing Fuses Changing the Battery FuseGeneral Cart Packaging Parts ListChapter 1. Assembling the Station 9476 Assembly and Setup Instructions Battery and Charger PackagingChapter 1. Assembling the Station Step 1 Attaching the Wheels and CastersTools You Need Washer Axle Mount Washer end cap Wheel Axle 9476 Assembly and Setup InstructionsAxle Caster Mount Socket Chapter 1. Assembling the Station9476 Assembly and Setup Instructions Step 2 Adjusting the Station’s HeightChapter 1. Assembling the Station Step 3 Attaching the Cabinet Handle and Cord BracketCord Bracket Handle Insert Step 4 Attaching Optional Items9476 Assembly and Setup Instructions F 4 1/4-20 x 3/4 hex bolts F 4 1/4-20 nuts F 4 1/4-20 washers Attach the Push HandleChapter 1. Assembling the Station 1. Remove the following items from their packaging F 1 push handle9476 Assembly and Setup Instructions Attach the Drop Shelf1-10 4. Finish tightening the screws to secure the support brace 1-11Chapter 1. Assembling the Station 9. Slide the metal rod through the slot in the side of the drop shelf and into the hole in the Station’s corner support. Push the rod until it exits through the hole in the other corner support. You may have to reach under the support brace to guide the rod into the opposite hole. Figure 1-129476 Assembly and Setup Instructions Terminal Cradle Magnet Attach the Data Entry Terminal Cradle1-13 Chapter 1. Assembling the Station9476 Assembly and Setup Instructions Step 5 Installing the Battery and ChargerInstall the Battery 1-14Retainer Rod 1-15Chapter 1. Assembling the Station 4. Slide the battery to the back of the cabinet 1-169476 Assembly and Setup Instructions Chapter 1. Assembling the Station 1-17Rubber Bracket Retainer Rod Ground Wire F 2 metal retainer rods F 1 rubber bracket Install the Battery Charger1-18 9476 Assembly and Setup InstructionsRetainer Rod 1-19Chapter 1. Assembling the Station 6. Place the charger on the cabinet floor 1-209476 Assembly and Setup Instructions Chapter 1. Assembling the Station 1-21Rubber Bracket Retainer Rod External Power Socket 9476 Assembly and Setup Instructions Step 6 Installing the PrintersAttach the Printer Brackets 1-22Chapter 1. Assembling the Station Attach the Printers1-23 Shoulder Screw 1-249476 Assembly and Setup Instructions Power Pack Battery WellFan-fold 1-25Chapter 1. Assembling the Station Shoulder Screw Printer BracketPrinter Port Cable 1-269476 Assembly and Setup Instructions Loading Supplies ChapterSupply Guide 9476 Assembly and Setup InstructionsPrinthead Assembly Platen Roller Pinch Rollers Peel Bar 2. Pull the supply guide forward and down as shown. FigureChapter 2. Loading Supplies Loading Fan-Fold Supplies4. Roll the O-rings out of their tracks and into the new positions 9476 Assembly and Setup InstructionsSupply Strip Fan-Fold Slot Magnetic Supply Bracket Chapter 2. Loading Supplies9. Feed the supply’s leading edge into the printer’s fan-fold slot. The black mark on the supply must be facing up if it is not, flip the supply stack over. Make sure the arrow printed on the back of the supply points toward the printer. Center the supply in the printer by lining up the black mark within the centering notch. Figure 9476 Assembly and Setup InstructionsSupply Deflector Chapter 2. Loading SuppliesSupply Guide Upper Opening 9476 Assembly and Setup InstructionsChapter 2. Loading Supplies Loading Roll Supplies in Fan-Fold PrintersSupply Holder Arrow Width of Supply Tabs 2-109476 Assembly and Setup Instructions Supply Holder 2-11Chapter 2. Loading Supplies nMake sure the supplies turn freely in the supply wellSupply Guide Upper Opening 2-129476 Assembly and Setup Instructions Supply Guide Upper Opening Lower Opening 2-13Chapter 2. Loading Supplies Use ribbon when printing on thermal transfer supplies Loading Ribbon2-14 9476 Assembly and Setup InstructionsChapter 2. Loading Supplies Reloading a Ribbon Cassette2-15 nDo Not wrinkle or crush the ribbon 2-169476 Assembly and Setup Instructions Chapter 2. Loading Supplies Printing2-17 Power Switch3. Turn each printer on and press each printer’s trigger to calibrate the supply. You are now ready to collect data and print 2-189476 Assembly and Setup Instructions Chapter 3. Charging the Battery 9476 Assembly and Setup Instructions Important Charging InformationChapter 3. Charging the Battery Battery Life9476 Assembly and Setup Instructions 3-4 Chapter TroubleshootingSolving Problems 9476 Assembly and Setup Instructions Changing the Battery FuseChanging Fuses 3. Pull the fuse out of the cover. Figure Chapter 4. Troubleshooting2. Open the Station’s cabinet. as shown until it pops out Press and turn the fuse cover Figure9476 Assembly and Setup Instructions Changing the AC Fuse6. Push the fuse holder until it snaps back into place. Figure Chapter 4. Troubleshooting7. Plug the power cord back into the power socket on the Station 4. Slide the fuse holder out and remove the fuse. Figure9476 Assembly and Setup Instructions Utility Cart SpecificationsBattery Weight9476 Assembly and Setup Instructions ChargerInput OutputPage Printed in the U.S.A For supplies, service, or assistance callTOLL FREE Published by the Technical Communications Department