PELCO EXSITE IPSXM
LANGUAGE | ENGLISH | |||
UNIT INVERSION | OFF | |||
<SYSTEM INFORMATION> |
| |||
<DISPLAY SETUP> |
| |||
<UNIT SETTINGS> |
| |||
<POSITION CALIBRATION> |
| |||
RESET CAMERA |
| |||
CYCLE CAMERA POWER |
| |||
REBOOT SYSTEM |
| |||
EXIT |
| |||
|
|
|
| |
|
|
|
|
|
UNIT SETTINGS |
| |||
|
| |||
<CAMERA> |
| |||
<MOTION> |
| |||
<POWER UP> |
| |||
<LINE SYNC> |
| |||
<PRESETS> |
| |||
<PATTERNS> |
| |||
<ZONES> |
| |||
<WINDOW BLANKING> |
| |||
<ALARMS> |
| |||
<WIPER> |
| |||
<AUX> |
| |||
<CLEAR> |
| |||
<PASSWORD> |
| |||
BACK |
| |||
EXIT |
| |||
|
| |||
|
|
|
|
|
PRESETS |
| |||
|
| |||
PRESET NUMBER | 1 | |||
***PRESET NOT DEFINED*** | ||||
<EDIT PRESET LABEL> |
| |||
<EDIT PRESET SCENE> |
| |||
<EDIT CAMERA SETTINGS> |
| |||
<MOTION DETECTION>* |
| |||
<CLEAR PRESET> |
| |||
<CLEAR CAMERA SETTINGS> |
| |||
BACK |
| |||
EXIT |
| |||
REFERENCE INFORMATION |
| |||
AZIMUTH | ||||
ELEVATION | ||||
ZOOM | ||||
CUSTOM CAMERA SETTINGS | ||||
ENABLE MOTION DETECTION (23X DAY/NIGHT CAMERA)
The following are the settings for MOTION DETECTION ENABLED:
OFF (default) | Motion detection is turned off (disabled). |
ON | Motion detection is turned on (enabled). |
NOTE: Motion detection does not work if the shutter speed is set at less than 1/60 of a second.
EDIT DETECTION AREAS (23X DAY/NIGHT CAMERA)
Four motion detection areas can be defined for a preset. Use the following steps to edit motion detection areas.
1.Edit detection areas 1, 2, 3, or 4:
a.Use the joystick to position the cursor beside EDIT DETECTION AREAS.
b.Press Iris Open. The EDIT DETECTION AREAS programming window appears on the monitor.
c.Use the joystick to position the cursor beside LOCATION for DETECTION AREA 1, 2, 3, or 4.
d.Press Iris Open. The cursor moves to the right next to the number 0.
e.Move the joystick up. A blue rectangle appears in the upper
f.Use the joystick to place the blue rectangle over the desired detection area.
g.Press Iris Open to make a selection.
NOTE: Motion detection is not guaranteed to catch 100% of activity.
MOTION DETECTION AREAS
MOTION DETECTION* |
|
|
|
MOTION DETECTION ENABLED | OFF |
<EDIT DETECTION AREAS> |
|
ACTIVATE AUX | OFF |
AUX TIME (SECS) | 0 |
BACK
EXIT
* Available only with the 23X day/night camera.
2.Set the sensitivity of the motion detection area:
a.Position the cursor next to SENSITIVITY for DETECTION AREA 1, 2, 3, or 4.
b.Press Iris Open, the cursor moves to the right.
c.Use the joystick to select one of the following sensitivity levels:
HIGH | The sensitivity level is high. Slight |
| changes in light level and contrast |
| are detectable. |
MEDIUM (default) | Average sensitivity. |
LOW | The sensitivity level is low. |
EDIT DETECTION AREAS*
DETECTION AREA 1
LOCATION0
SENSITIVITYMEDIUM
DETECTION AREA 2
LOCATION0
SENSITIVITYMEDIUM
DETECTION AREA 3
LOCATION0
SENSITIVITYMEDIUM
DETECTION AREA 4
LOCATION0
SENSITIVITYMEDIUM
BACK
EXIT
d.Press Iris Open to make selection.
Quick Programming Guide
(See Page 9)
29 |
