SET WASHER SEQUENCE
PELCO EXSITE IPSXM
LANGUAGE | ENGLISH |
UNIT INVERSION | OFF |
<SYSTEM INFORMATION> |
|
<DISPLAY SETUP> |
|
<UNIT SETTINGS> |
|
<POSITION CALIBRATION> |
|
RESET CAMERA |
|
CYCLE CAMERA POWER |
|
REBOOT SYSTEM |
|
EXIT |
|
UNIT SETTINGS
<CAMERA>
<MOTION> <POWER UP> <LINE SYNC> <PRESETS> <PATTERNS> <ZONES>
<WINDOW BLANKING> <ALARMS> <WIPER>
<AUX>
<CLEAR>
<PASSWORD>
BACK
EXIT
WIPER*
WIPER CONTROL | AUX 1 |
WIPER MODE | CONTINUOUS |
WIPER DWELL (SECS) | 2 |
WIPER TIME (MINS) | 60 |
|
|
<SET WASHER SEQUENCE> |
|
BACK |
|
EXIT |
|
SET WASHER SEQUENCE*
* * * PRESET NOT DEFINED * * * |
|
<EDIT PRESET LABEL> |
|
<EDIT PRESET SCENE> |
|
<EDIT CAMERA SETTINGS> |
|
WASHER TIME (SECS) | 4 |
WIPER DELAY (SECS) | 1 |
AUTO RETURN | ON |
<CLEAR PRESET> |
|
<CLEAR CAMERA SETTINGS> |
|
BACK |
|
EXIT |
|
REFERENCE INFORMATION |
|
AZIMUTH | - - |
ELEVATION | - - |
ZOOM | - - |
CUSTOM CAMERA SETTINGS | - - |
* Available only with the wiper models. |
|
An external washer (not supplied by Pelco) can be used to wash the window of the enclosure. Accessing AUX 3 or selecting Preset 87 will start the washer sequence.
Use the following steps to program the washer sequence.
1.Use the joystick to position the cursor beside WIPER and then press Iris Open. The wiper menu appears on the monitor.
2.Position the cursor beside SET WASHER SEQUENCE and then press Iris Open.
3.Edit the preset label:
a.Use the joystick to position the cursor beside EDIT PRESET LABEL.
b.Press Iris Open. The following appears on the monitor:
LABEL FOR PRESET WASH |
|
WASH - - - - - - - - - - - - |
|
1234567890 | OK |
ABCDEFGHIJ | CANCEL |
KLMNOPQRST |
|
SPACE | |
abcdefghij | BACKSPACE |
klmnopqrst |
|
uvwxyz#&:” |
|
c.Use the joystick to position the cursor beside a character. Press Iris Open to enter selection. To clear a character, position the cursor beside BACKSPACE, and then press Iris Open.
d.When the label is completed, move the cursor to OK. Press Iris Open to return to the Set Washer Sequence menu.
4.Edit the preset scene:
a.Use the joystick to position the cursor beside EDIT PRESET SCENE.
b.Press Iris Open.
c.Follow the directions displayed on the monitor.
5.Edit preset camera settings:
a.Use the joystick to position the cursor beside EDIT CAMERA SETTINGS.
b.Press Iris Open. The EDIT CAMERA SETTINGS window appears on the monitor. Refer to the Camera and Advanced Camera Settings sections of this manual to change camera settings
6.Set the washer time. The washer time programs how long the wiper will be on before it automatically shuts off. Washer time can be programmed from 4 to 60 seconds.
7.Program the wiper delay. Wiper delay programs when the wiper will start after the washer sequence has started. Wiper delay can be programmed from 1 to 30 seconds.
8.Program the Auto Return to ON or OFF. If the auto return is set to ON the unit will return to the last operation before the system started the washer sequence. If it is set to OFF, the system will remain at the preset scene for the washer sequence.
Quick Programming Guide
(See Page 9)
39 |
