Philips DMR-XS350EB Testing the connection, Setting the IP address, Setting the DNS-IP, 106

Network Settings

These settings are used when you will connect this unit to a network. The connection to the Internet may take time or the internet may not be connected depending on the connection environment. It is recommended that you use a broadband connection.

Testing the connection

Always test the connection when a LAN cable is connected or when new “IP Address/DNS Settings” have been made.

Press [FUNCTION MENU].

Press [e, r] to select “Others”, then press [OK]. Press [e, r] to select “Setup”, then press [OK].

Press [e, r] to select “Network Settings”, then press [OK].

Press [e, r] to select “IP Address/DNS Settings”, then press [OK].

IP Address / DNS Settings
Connection Test
IP Address Auto-assignment	On
IP Address
Subnet Mask
Gateway Address
DNS-IP Auto-assignment	On
Primary DNS
Secondary DNS
Connection Speed Auto-configure	On
Connection Speed Setting
MAC Address: 00-0b-97-e6-7a-ae
OK
RETURN
Press [e, r] to select “Connection Test”, then
press [OK].

“Testing”	: The test is in progress.
“OK”	: The connection is completed.
“Failed”	: Please check the connection and settings.

Notes

•Perform the “Connection Test” also when any change was made to the “IP Address / DNS Settings”.

•If the connection test fails, it may be necessary to set the MAC address of this unit at the router side. The MAC address can be displayed by selecting “Network Settings” and “IP Address / DNS Settings” in steps − (➔ above).

Setting the IP address

In most cases, default settings can normally be used without making any changes.

Set the IP address only when the router has no DHCP server functions or when the router’s DHCP server function is disabled.

After performing steps – (➔ above)

Press [e, r] to select “IP Address Auto- assignment”, then press [w, q] to select “Off”.

Press [e, r] to select “IP Address”, “Subnet Mask” or “Gateway Address”, then press [OK].

8Enter numbers with the numbered buttons, then

press [OK].

After checking the specifications for your broadband router, enter each number.

If the number is unknown, then check the number of other devices such as personal computers connected via a LAN cable. Assign a different number from those of other devices for “IP Address” and the same number for others. If a wrong number is entered, then press [DEL].

106

IP Address

Please input IP Address and press “OK”. The IP address will be cleared by pressing “OK” when there is no number input. Press “DEL” button if a wrong number is entered.

192	.	1	.	.
0 -	9	Number

9Press [w, q] to select “Yes”, then press [OK].

Notes

• The numeric input range is between 0 and 255.

Setting the DNS-IP

In most cases, default settings can normally be used without making any changes.

When setting an assigned DNS server from your internet service provider, perform the following settings.

After performing steps – (➔ left)

Press [e, r] to select “DNS-IP Auto-assignment”, then press [w, q] to select “Off”.

Press [e, r] to select “Primary DNS” or “Secondary DNS”, then press [OK].

8Enter numbers with the numbered buttons, then press [OK].

Follow the instructions given by your internet service provider and enter the numbers. If the number is unknown, then check the number of other devices such as personal computers connected via a LAN cable and assign the same number.

If a wrong number is entered, then press [DEL].

9Press [w, q] to select “Yes”, then press [OK].

Notes

•The numeric input range is between 0 and 255.

Setting the connection speed

When the connection test results in “Failed” after the IP and DNS-IP addresses are assigned, perform the following settings.

After performing steps – (➔ left)

Press [e, r] to select “Connection Speed Auto- configure”, then press [w, q] to select “Off”.

Press [e, r] to select “Connection Speed Setting”, then press [w, q] to select a connection speed.

Select a connection speed in accordance with the environment of the network connected.

When the settings are changed, the network connection may be disabled depending on the device.

RQT9431