Philips DMR-XS350EB operating instructions Messages, On the Unit’s Display, 116

Messages

On the Unit’s Display			Page
H	, F	• An error has occurred. The number following “H” or “F” depends on the status of the unit.	−
(“	” stands for a service	Check the items below and in the Troubleshooting Guide. If the service number still does
number.)		not disappear after the check, reset the unit (➔ 119, “To restore the unit if it freezes” ).	−
		• If the service numbers fail to clear, note the service numbers and contact a
		qualified service person.
DVD		• The remote control and the main unit are using different codes. Change the code	119
(“	” stands for a number.)	on the remote control.
EXT-L		• This unit is in EXT LINK standby. EXT LINK has been turned on and will stop	62
		operation on the unit until the recording has completed.
		Press [EXT LINK] to stop recording or cancel linked timer.
FINISH		• The software update is completed.	108
GUIDE		• TV Guide data is being downloaded.	44
HARD ERR		• If there is no change after turning the unit on and off, consult the dealer where the	−
		unit was purchased.
NoERAS		• You cannot delete items on this disc.	−
		The disc may be damaged. Use a new disc.
NoREAD		• The disc is dirty or badly scratched. The unit cannot record, play, or edit.	118
		• The disc may be incompatible or of poor quality.	21, 22
		• You have used a lens cleaner and it has finished operation. Press	7
		[; OPEN/CLOSE] on the main unit to eject the disc.
NoWRIT		• You cannot write to this disc.	−
		The disc may be damaged. Use a new disc.
PLEASE WAIT		• Displayed when the unit is started or when turned to standby. This is not a	−
		malfunction.	−
		• The unit is carrying out its recovery process. You cannot operate the unit while the
		message is displayed.
PROG FULL		• There are already 32 timer recording programmes. Delete unnecessary timer recording programmes.	41
REMOVE		• The USB device is drawing too much power. Remove the USB device.	−
START		• Update of the software is started.	108
		You cannot operate the unit until the update is complete.
SW-DL		• The unit is performing a software update.	108
		Download will stop when the power is turned on, or the timer recording starts.
UNFORMAT		• You inserted an unformatted DVD-RAM, DVD-RW, +RW, an unused +R, +R DL or	93
		DVD-RW (DVD-Video format) that has been recorded on other equipment.
		Format the disc to use it.
		However all the recorded contents on the disc are deleted.
UNSUPPORT		• You have inserted a disc the unit cannot play or record onto.	21, 22
		• You tried to operate with a non-compatible USB memory.	23
UPD /		• The software is being updated.	108
(“	” stands for a number.)	You cannot operate the unit until the update is complete.
U50		• The terminal, antenna cable or DISH is short-circuited as for both DISH IN 1 and	10, 11
		DISH 2. Check the connection status.
U50 1		• The terminal, antenna cable or DISH is short-circuited as for DISH IN 1. Check the connection status.	10, 11
U50 2		• The terminal, antenna cable or DISH is short-circuited as for DISH IN 2. Check the connection status.	10, 11
U59		• The unit is hot.	−
		The unit switches to standby for safety reasons. Wait for about 30 minutes until
		the message disappears.
		Select a position with good ventilation when installing the unit. Do not block the
		cooling fan on the rear of the unit.
U61		• (When a disc is not inserted) Displays when a malfunction has occurred during recording	−
		or playback. This is displayed when the unit is in the recovery process to return to normal
		operation; it is not broken. Once the display clears you can use the unit again.
U72		• The HDMI connection acts unusually.	−
U73		– The connected equipment is not HDMI compatible.
		– Please use HDMI cables that have the HDMI logo (as shown on the cover).
		– The HDMI cable is damaged.
U76		• HDMI cannot be output because you are connected to a model that does not	−
		support copyright protection.
U77		• Due to the current disc not having authorised copyright information, video output is not performed.	−
U88		• There was something unusual detected with the disc while recording, playing or	121
		copying; there was a power failure or the AC mains lead was disconnected while the
		unit was on. The unit is carrying out its recovery process. This process restores the
		unit to normal operation. The unit is not broken. Wait until the message disappears.
U99		• The unit fails to operate properly. Press [8] on the main unit to switch the unit to	−
		standby mode. Now press [8] on the main unit again to turn the unit on.
X HOLD		• The HOLD function is activated.	105
		Press and hold [OK] and [BACK/RETURN ] at the same time until “X HOLD” disappears.

116

The message is alternately displayed.

RQT9431