Color has Irregularity, Yes | Philips V30 guide

94

107T5

Go to cover page

General Troubleshooting Guide

7

Color has

irregularity

Have you changed the

tilt or swivel angle

of the monitor?

YES

Press OK " OK " button

Select "EXTRA CONTROLS"

Are there any stray fields such as magnetic and

speaker near the monitor?

Keep any stray magnetism away from the computer.

Did you adjust the red, green, and blue colors?

YES

Select "RESET TO FACTORY

SETTINGS"

Press the OK	OK	button
Press the OK		button
Bring up "EXTRA CONTROLS"			YES
window
			Is picture displayed
			normally?
			YES
		69	85
			END
Press the DOWN		button
to select "DEGAUSS",
then press OK " OK " button
			NO
Is picture displayed			NO
normally?			NO
normally?
YES
END

NO

* Keep any stray magnetism

away from the computer. * Reset to Factory settings.

* Press "DEGAUSS" selection.

Unsuccessful

It is need to check and

repair the monitor.

Press the OK OK button

Bring up "RESET TO FACTORY SETTINGS" window

Press the DOWN button

to select "YES"

Is picture displayed

normally?

YES

	Press the OK	OK	button
	Press the OK	OK	button
	Press the OK	OK	button
	Press the OK		button
	YES
	END

Image 94

Philips V30 manual Color has Irregularity, Yes

Contents

Service Auto Scan Colour Monitor ChassisV30 Important Safety Notice Technical Data This monitor has 8 factory-preset modes as indicated Front View Rear view Front control OSD menu tree OSD Tree OSD Adjustments Language Brightness Zoom Adjust Shape Adjust Side Angles Reset to Factory Settings Extra Controls Adjust Moire OSD Adjustments , Troubleshooting Degauss Lock/Unlock, Factory Mode, Burn In, Service Mode Wiring Diagram General CRT grouding wirel Video PanelMechanical Instructions Clip Pedestal assy Screw Main panel with Bottom Tray Screw Video panel Main panel Are indicated by the symbol ESD Pre warm-up ========== Electrical InstructionsGeneral point ========== Main chassis alignment ================== CRT Adjustment of Moir ================ Adjustment procedureFocus adjustment ============= Default settings ============== DDC Instructions General This is for initialize alignment box Configuration and procedureInstallation of EDID301.EXE Method 1 Start on DDC program Method 2 After create a shortcut of EDID301.EXE Read DDC data from monitor Videocard PrinterportLTP1 DC Power ~12 Video cableModify DDC data verify Edid version, week, year Modify DDC data Monitor Serial No Write DDC data Confirm Serial Number in User ModeSave DDC data Load DDC data DDC only was disabled as shown in FigExit DDC program Hex Data of DDC2B PHL 27X 28X 107T5 Video Function Block of V30 107T5 Schematic Diagram of Main board Main PCB 107T5 A. of Main board A. of Main board Schematic Diagram of Video board Video PCB A. of Video board A. of Video board Schematic Diagram of Control board Control PCB A. of Control board Exploded View Recommend Parts List Model V30 107T50/00 Spare Parts List Model V30 107T50/00 Audio Panel General Product Specification LOW Emission MPRII/TCO99/TCO95 optional Index 5903 Introduction Electrical characteristicsGeneral description 64.0 KHz 60Hz Vesa Factory preload modes Display size 11.093 Rear porch 222 us 578 ms Sync width Total size 11.764 Display sizeSync width 069 ms Sync polarity Total size 21.333 13.333 Display size 16.162 = 12.8 ms Rear porch 200 us 607 ms Sync width 106 ms Sync. polarity Total size 13.417 Display size Total size 13.853 Display sizeDisplay size 12.552 Rear porch 911 us 784 ms Sync width 59012 Implosion protection By P-Mini-rim-band Power supplyVertical scanning Scanning frequency 50 160 Hz Shift range 25.0 1 KV Ib=0 Display Light Output MVpp cross hatch Max Image size For preset modes only100% Max. Y. min Non-linearity = 100% For 6500 K 015 For SRGB = 0.313 Sweden SwitzerlandBelgium Finland Norway Sets Layer Block Blocks / Container Total Sets Tilt and swivel base Tilt angle200 Nsta Finland Taiwan Practice of Mtbf = NBR. of Failure Sets FIG-1 Image Dimension FIG-2 Image Centering FIG-3 Image Rotation FIG-4 Image Geometry FIG-5 Contrast and Brightness Measurement Area FIG-6 Misconvergence 230 mm Focus check character Repair Flow Chart = + 2V ABL Check Check list Repair Flow Chart Check sync Eeprom Check idle status sda=pin32=hi scl=pin31=hi Ewdrv Vblk Definitions InstallationLightFrame for Windows Compatibility Uninstall LightFrame for Windows Operating LightFrame How to Deactivate LightFrameHow To Activate LightFrame Icon and Colors User clicks full First target selected Window restored LF suspendUser clicks off or full screen Screen button Full screen Removal of SMDs Repair TipsGeneral cautions on handling and storage Attachment of SMDs Test current 25A,AC Test time Safety test requirementsTest 2820VDC 1700VDC Voltage 2000VAC 1200VAC Required =0.09+R ohm, R is the resistance of the mains cord OSD main General Troubleshooting GuideBuzzing sound when powering on Menu locked No DISPLAY, but LED is on Or LED is amberyellow YES END Settings Picture is too bright or dark Plug & Play is not Active normally Power management function is not active Buzzing sound when powering on No Power / LED is off Color has Irregularity YES Picture distortion is Not adjusted normally Press the OK Picture is not stable Need to change display size and adjust distortion Color Patterns visible On the screen Moire OSD Main Menu Locked It is need to check Environment problemVideo system Problem Repair the monitor Missing Color Color Purity Does degaussing resolve ? 104 107T5 107T5 105 CustoMax Colorific USB 107T5 109