Pioneer SC-35 manual Using other functions Chapter, Setting the Audio options

09Using other functions

Chapter 9:

Using other functions

Important

•The procedure for setting the receiver operation mode differs for the remote controls included with the SC-37 and SC-35. For the SC-37’s remote control, set the remote control operation selector switch to RECEIVER. For the SC-35’s remote control, press the

RECEIVER button. When “set the remote control to

Setting	What it does
DELAY	Some monitors have a slight
(Sound	delay when showing video, so the
Delay)	soundtrack will be slightly out of
	sync with the picture. By adding a
	bit of delay, you can adjust the
	sound to match the presentation
	of the video.

Option(s)

0.0to 10.0 (frames)

1 second = 30 frames (NTSC)

Default: 0.0

the receiver operation mode” is indicated in these instructions, use the respective procedure described above.

Setting the Audio options

There are a number of additional sound settings you can make using the AUDIO PARAMETER menu. The defaults, if not stated, are listed in bold.

Important

•Note that if a setting doesn’t appear in the AUDIO PARAMETER menu, it is unavailable due to the current source, settings and status of the receiver.

1Set the remote control to the receiver operation mode, then press AUDIO PARAMETER.

2Use / to select the setting you want to adjust. Depending on the current status/mode of the receiver, certain options may not be able to be selected. Check the table below for notes on this.

3Use / to set as necessary.

See the table below for the options available for each setting.

4 Press RETURN to confirm and exit the menu.

Setting	What it does	Option(s)
MCACC	Selects your favorite MCACC	M1. MEMORY 1
(MCACC	preset memory when multiple	to
preset)	preset memories are saved. When	M6. MEMORY 6
	an MCACC preset memory has	Default:
	been renamed, the given name is	M1. MEMORY 1
	displayed.
EQ	Switches on/off the effects of EQ	ON
(Acoustic	Pro.
		OFF
Calibration
EQ)
S-WAVE	Switches on/off the effects of	ON
(Standing	Standing Wave Control.
		OFF
Wave)

MIDNIGHT	Allows you to hear effective	MIDNIGHT/
	surround sound of movies at low	LOUDNESS
	volumes.	OFF
		MIDNIGHT ON
LOUDNESS Used to get good bass and treble
		LOUDNESS
	from music sources at low
		ON
	volumes.
TONE	Applies the treble and bass tone	BYPASS
(Tone	controls to a source, or bypasses
		ON
Control)	them completely.
BASSa	Adjusts the amount of bass.	–6 to +6 (dB)
		Default: 0 (dB)
TREBLEa	Adjusts the amount of treble.	–6 to +6 (dB)
		Default: 0 (dB)
S.RTRV	With the Sound Retriever	OFFb
(Sound	function, DSP processing is used
		ON
Retriever)	to compensate for the loss of
	audio data upon compression,
	improving the sound’s sense of
	density and modulation.
DNR	May improve the quality of sound	OFF
(Digital	in a noisy source (for example,
		ON
Noise	video tape with lots of background
Reduction)	noise) when switched on.
DIALOG E	Localizes dialog in the center	OFF
(Dialog	channel to make it stand out from
		FLAT
Enhance	other background sounds in a TV
		UP1/UP2/UP3/
ment)	or movie soundtrack. By moving
		UP4c
	from UP1 through UP2 and UP3
	up to UP4, you can make the
	sound source seem to relocate
	upwards.
Hi-bit32	Creates a wider dynamic range with	OFF
(SC-37 only)	digital sources like CDs, DVDs or
		ON
(Hi-bit32/	BDs. Smoother, more delicate
High-	musical expression can be achieved
Sampling)	by requantizing 16 bit PCM or 20 bit
	compressed audio signals or 24 bit
	compressed/lossless audio signals
	to 32 bit.
Hi-bit	Creates a wider dynamic range with	OFF
(SC-35 only)	digital sources like CDs or DVDs.
		ON

(High Bit/	Smoother, more delicate musical
	expression can be achieved by
High
	requantizing 16 bit PCM or 20 bit
Sampling)
	compressed audio signals to 24 bit.

76

En