Program, 7LPH | Powerware FE/QFE UPS instruction

NOTE If the ALARM indicator is on, read the alarm message on the control panel display, turn the ON/OFF and DC switches to the OFF position, and call your service representative.

For Plug-Receptacle UPSs: Turn the AC input power on at the service panel. The AC LINE indicator illuminates. After a few seconds, the UPS switches from battery power to AC input power. The BATTERY POWER indicator turns off.

For Hardwired UPSs: Turn the AC line disconnect switch to the ON position. The AC LINE indicator illuminates. After a few seconds, the UPS switches from battery power to AC input power. The BATTERY POWER indicator turns off. Now, turn the UPS bypass switch (either on the back of the UPS or mounted nearby) to the UPS position.

NOTE The UPS and external battery cabinets are shipped with the batteries charged. However, batteries may lose some of the charge during shipping and storage. You can use the UPS immediately after unpacking, but it may not provide the full-rated backup time during a power failure. Upon initial startup, the UPS may need to operate for

24 hours before the battery is fully charged and full battery-backup time is available. If the CHARGING indicator is illuminated, operate the UPS for 24 hours to fully charge the battery.

od For Plug-Receptacle UPSs: Plug the equipment you want to protect into the UPS receptacles and turn on the equipment. If the ALARM indicator illuminates, see “Alarms” on page 59.

For Hardwired UPSs: Turn on the equipment connected to the UPS. If the ALARM indicator illuminates, see “Alarms” on page 59.

rd Set the time and date using the control panel.

NOTE The correct time and date for is needed for the UPS alarm and inverter logs.

Reset the time and date whenever the UPS has been shut down.

Time is parameter 0; see “Parameters” on page 32 for more information. To set the time, follow these steps:

	Press this key:	Display shows:
	[DISPLAY]	'LVSOD\
	[0]	'LVSOD\
	[ENTER]	7LPH
	[PROGRAM]	3JP
20	Powerware® FERRUPS FE/QFE UPS (500 VA–18 kVA) User’s Guide : Rev A www.powerware.com

Image 26

Powerware FE/QFE UPS manual Program, 7LPH

Contents

Powerware Ferrups FE/QFE UPS Page Powerware Ferrups FE/QFE UPS For Users in Germany Class a EMC StatementsFCC Part ICES-003 Table of Contents Alarm Code Summary Service and Support Options KVA Models 500 VA-3.1 kVA Models IntroductionIdentifying Your UPS Page N G E R Safety WarningsP O R T a N T S a F E T Y I N S T R U C T I O N S R N I N G R E SikkerhedsanvisningerU T I O N V a a R Belangrijke VeiligheidsinstructiesV a R S E L A R S C H U W I N G A R a Tarkeita TurvaohjeitaG E L E T R O I T U S Consignes de sécurité R O H T U N G SicherheitswarnungenR N U N G „Ò·Ûﬂ· C›„ÈÛÙ.ÃÁ˜ÒÁÙÈÏÔﬁ95%ÔÈÂﬂÙÂUPSÍÔÌÙ‹ÛÂÌÂÒ¸ﬁ V E R T E N Z a Avvisi di sicurezzaR I C O L O R L I G Viktig SikkerhetsinformasionT E N Z I O N E I D a D O Regulamentos de SegurançaR S I K T I G V E R T Ê N C I a Îïàñíî Ïðåäóïðåæäåíèÿ ïî ìåðàì áåçîïàñíîñòèR I G O Ðåäóïðåæäåíèå L I G R O Advertencias de SeguridadÑòîðîæíî V E R T E N C I a R a SäkerhetsföreskrifterE C a U C I Ó N K T I G T UPS Startup Startup for the FE and QFE 500 VA-3.1 kVA UPS Ld The AC Line indicator illuminates see Figure Startup for the FE and QFE 4.3-18 kVA UPS Program 7LPH Where is the Battery Ah value from Table DWH External Battery Pack Ah Values 9ME Switch On/Off Switch Power Cord RS-232 Communication PortRS-232 Communication Port On/Off Switch Rear Panels Panel KVA Models Front Panel Indicators Operation Indicator Status Using the Control Panel Changing Operating Modes Entering Passwords Operating Modes Displaying and Changing Parameters Locking and Unlocking the Control Panel Using the Configuration Menu Remote Control Panel Logic Test Battery TestAutomatic System Test Inverter Test Parameters Parameters VA Limit, parameter DC power is turned offUPS Low Shows -63c Configured for use with your networkSwitch is in the OFF position Used by your equipment Explanation UPS ShutdownInverter Logs on Each part of the system test see U T I O N Extended Power Outages Page Powerware Software Suite Communication Communication Port Connecting a Terminal or Computer to the RS-232 Port DB-9 to UPS Pinout Action Key Sequence DB-25 Port SettingsKeystroke Commands Entering Commands from a Terminal or Computer Commands Shows a list of terminal/computer commands CommandDelay Command then clears the minimum and maximum values Shutdown cancel PasswordUPS restar hortly after power returns Cancels a shutdown started with the shutdown command Remote Monitoring Remote ShutdownPage Options Page Maintenance Page Specifications FE and QFE 4.3-18 kVA E9I I9G Audible Noise dB Runtime minutes Full Load Half Load WeightF9E uWA G9E uWA IuWA 103A 149A Electrical Input and Output Environmental and Safety BatteryPage Troubleshooting Alarms Alarms Possible microprocessor problem To start the user test alarm fromAlarm off Temperature probe is missing or Requires service Representative Alarm and Inverter LogsReading the Alarm Log from a Control Panel UPS off and contact your service Reading the Inverter Log from a Control Panel Reading the Alarm Log from a Terminal or Computer Inverter Codes Reading the Inverter Log from a Terminal or Computer Alarm Code SummaryLow Battery Low AC Output Service and Support 852--3030