R

7100FP EPA Woodburning Fireplace

Suggestions:

1.Insulate chase.

2.Finish chase walls with dry wall 5/8 in. (16mm) Type X face tape.

3.All dimensions are to finished walls and ceilings.

Figure 13.1 Sheetrocked Chase

WARNING

Fire Risk

Comply with all minimum clearances speci- fied.

•A minimum 1/2 in. (13mm) air clearance must be maintained at the back and 1 in. (25mm) to the sides of the fireplace assembly.

•Chimney sections at any level require a 2 in. (51mm) minimum air space clearance between the framing and chimney section.

WARNING

Fire Risk

Do not apply combustible finishing materials over any part of the front of this fireplace.

•The metal fireplace face may only be covered with noncombustible materials such as ceramic tile, brick, or stone.

•Do not cover or block any cooling air slots.

The decorative fascia must be removable for future serviceability of the Automatic Combustion Control.

WARNING

Fire Risk

•Maintain clearances.

•Use only non-combustible material below standoffs, material such as cement board is acceptable.

•Framing or finishing material used on the front of, or in front of, the appliance closer than the minimums listed, must be constructed entirely of noncombustible materials (i.e., steel studs, concrete board, etc.).

D. Electrical Access and Wiring Diagram

NOTE: The manual override switch, rheostat speed control and cover plate are supplied. You will need to supply: 14-3 wire with ground; 14-2 wire with ground; standard wall mount junction box; wire nuts.

1.Remove junction box cover plate on the bottom right side of the fireplace.

2.Thread the 14-3 with ground wire through the opening with the strain relief on the cover plate.

3.Match colors to wire harness, (red to red, white to white, etc) and secure with wire nuts.

NOTE: Wiring for blowers must be done before framed enclosure is completed. If using a Heat Zone kit, it also must be installed before enclosure is complete.

 

14-3 w/ground

Match colors to wire

WHITE

harness (red to red,

 

white to white, etc) and

 

secure with a wire nut

 

Power to the Fireplace

 

Snap Disc

RED

bypass switch

 

BLACK

Figure 13.2 Fan Wiring Diagram

Standard wall mount with

Junction Box

14-2 w/ground

WIRE NUT

WHITE

GREEN

BLACK

(110V)

 

Incoming Power

September 7, 2007

433-1390D

Page 13

Page 12 Page 14
Page 13
Image 13
Quadra-Fire 7100FP-BK-B, 7100FP-NL-B, 7100FP-GD-B warranty Electrical Access and Wiring Diagram, Suggestions
Page 12 Page 14

7100FP-BK-B, 7100FP-GD-B, 7100FP-NL-B specifications

The Quadra-Fire 7100FP series, including the models 7100FP-BK-B, 7100FP-NL-B, and 7100FP-GD-B, represents an exceptional choice for homeowners seeking efficient and powerful heating solutions. These fireplaces are designed to provide warmth and ambiance while incorporating advanced technologies that enhance performance and ease of use.

One of the primary features of the 7100FP series is its large viewing area, which allows homeowners to enjoy the mesmerizing flames while increasing the aesthetic appeal of any living space. The generous size of the firebox ensures that it can accommodate sizable logs, providing longer burn times and requiring less frequent reloading. This feature is particularly beneficial for those who appreciate an extended, leisurely evening by the fire.

A hallmark of the Quadra-Fire brand is its innovative heating technology. The 7100FP models are equipped with the patented Quadra-Fire combustion system, which promotes a cleaner burn and maximizes heat output. This system utilizes secondary combustion technology that burns off excess gases and particulates, resulting in a more environmentally friendly fire that emits fewer emissions compared to traditional wood-burning fireplaces.

Additionally, the 7100FP series includes advanced airflow designs that facilitate efficient heat distribution throughout the room. The adjustable air control allows users to easily regulate the burn rate and heat output, ensuring optimal comfort at any time. With a variety of trim options available, including the sleek black, traditional natural, and modern gold finishes, homeowners have the flexibility to choose a model that complements their interior decor.

Moreover, the 7100FP series is designed with user convenience in mind. For easy cleaning and maintenance, they include a removable ash pan feature. A glass viewing window is treated with a special coating, preventing soot buildup and allowing for uninterrupted views of the flames.

In terms of safety, the 7100FP units are equipped with a tempered glass door that is designed to withstand high temperatures, ensuring that the fireplace is safe for family gatherings. Overall, the Quadra-Fire 7100FP-BK-B, 7100FP-NL-B, and 7100FP-GD-B models seamlessly combine style, efficiency, and comfort, making them a top choice for those seeking a modern solution to home heating. With innovative technology and a commitment to performance, these fireplaces enhance any home’s ambiance while providing reliable warmth.
Top Page Image Contents