CB1200-I Pellet Insert Panel and Trim Set | Quadra-Fire CB1200I

CB1200-I Pellet Insert

R

F. Panel and Trim Set

Standard Size: 30 inches H x 40 inches W (762mm x 1016mm)

Large Size: 33 inches H x 50 inches W (838mm x 1270mm)

Included in Kit: 2 side panels, 1 top panel, 2 side trim, 1 top trim, 2 corner brackets and fastener package.

Tools Needed: Phillips and flat head screw drivers.

1.Unpack and lay out parts face down (flanges up) on a non- abrasive surface as shown in Figure 22.1. Install (1) 8-32 x 3/8 inch screw into bottom tab of side panel.

2.Set the large hole at bottom of side curtain over screw installed in Figure 22.3.

3.Stand assembly on end and attach and install (1) 8-32 x 3/8 inch screw through tab in side panel and curtain. Figure 22.4. Lay face down as shown in Figure 22.5.

4.Align top panel to side panel setting clearance hole over screw head in side panel/curtain assembly. Install (2) 8-32 x 3/8 inch screws through holes in side panel into top panel. Figure 22.6. Complete for both sides.

Corner	Top Trim	Corner
Bracket	Top Trim	Bracket
Right	Top Panel	Left
Right		Left
Trim		Trim

Right	*Right Side	*Left Side	Left
Panel	Curtain	Curtain	Panel

Figure 22.1

NOTE: *Right and left side curtains are shipped with the insert.

Figure 22.3

Figure 22.4

Figure 22.5



			Figure 22.6
	Figure 22.2		Figure 22.6
	Figure 22.2


Page 22		7014-188B	February 3, 2010

Image 22

Quadra-Fire CB1200I, CB1200MI-MBK owner manual CB1200-I Pellet Insert Panel and Trim Set

Contents

CB1200MI-MBK Hot glass will cause burns CB1200-I Pellet Insert Welcome to the Quadra-Fire Family Table of Contents Listing and Code Approvals Appliance Certification BTU & Efficiency SpecificationsGlass Specifications Mobile Home Approved Design, Installation & Location Consider- ations Appliance Location Thermostat Location CB1200-I Pellet Insert Locating Your Appliance & ChimneyNegative Pressure Draft Tools And Supplies Needed CB1200-I Pellet Insert Fire SafetyInspect Appliance & Components and Pre-Use Check List 3Dimensions and Clearances Appliance Dimensions Shown with Rear Vent and Optional Outside Air Rear Shroud Kit is Required for Built-In InstallationInch 0mm Clearance to Exposed Section and Face Trim Floor Protection Zero Clearance InstallationsNon-Zero Clearance Installations Inches Millimeters Converting k to R Thermal Conductivity k valueThermal Resistance R value Converting R to k Altering the Factory-Built Fireplace S629M, Standard for 650oC FACTORY-BUILT Chimneys Chimney and Exhaust Connection Vent InformationVenting Termination Requirements CB1200-I Pellet Insert Equivalent Feet of Pipe Pipe Selection ChartExample of 3 Elbow-Rear Vent Termination Calculation Venting Systems Full Reline With Outside Air Horizontal CB1200-I Pellet Insert Full Reline With Outside Air Vertical Mobile Home Rear Shroud Installation 7Appliance Set-Up For Top Vent Installation Rear Vent Installation PreparationInstalling Rear Shroud Attaching Shroud to Hopper Body To adjust hopper Adjustable Hopper OptionsGrille Installation CB1200-I Pellet Insert Outside Air Kit Instructions Adjustable Hearth Support Size 9D x 45W, 2 to 10 Height Adjustment CB1200-I Pellet Insert Panel and Trim Set CB1200-I Pellet Insert Panel and Trim Set Cont’d Completed View CB1200-I Pellet Insert Optional Brick Set Installation Brick Clip Installation Right Thermostat InstallationTop Log, Left Front Log Wood Pellets Shelled Field Corn Cont’d 8Operating InstructionsFuel Size, Material and Storage Shelled Field Corn Starting Your First Fire CB1200-I Pellet Insert General Operating InformationBefore Your First Fire Thermostat Calls For Heat Feed Rate Adjustment Instructions CB1200-I Pellet Insert Fire CharacteristicsIgnition Cycles CB1200-I Pellet Insert Frequently Asked Questions Issues Solutions Troubleshooting Symptom Troubleshooting Cont’d Symptom Possible Cause Corrective Action Troubleshooting Cont’d Maintaining & Servicing Your Appliance 10Proper Shutdown ProcedureQuick Reference Maintenance Chart Types of Fuel Cleaning the Hopper Cleaning Firepot with Cleaning Rod & Firepot Clean-Out ToolCleaning Ash Pan See Disposal of Ashes Frequency As needed Cleaning Exhaust Path Cleaning Heat Exchanger Chambers & Drop TubeCleaning Beneath Heat Exchanger Cleaning the Glass Door Gasket Inspection Cleaning Exhaust Blower Requires No LubricationPreparing Firebox for Non-Burn Season Frequency Yearly CB1200-I Pellet Insert High Ash Fuel Content Maintenance Immediate Attention and Cleaning is Required Before removing the side frame. Use a pow Ered Phillips head screw driver to remove Screws Igniter Replacement Baffle Removal CB 200-I Pellet Insert Reference MaterialsComponent Function Thermostat Vacuum SwitchWiring Harness See .1 below Snap Disc #1 Convection Blower 125F CB1200-I Pellet Insert Component Locations Control Box CB1200-I Pellet Insert Exploded Drawing CB1200-I Pellet Insert Service Parts and Accessories Important this is Dated Information HOW to Order Stocked At Depot Description Comments Part Number DR-CB12-NL-B Stocked Description Comments Part Number CB1200-I Pellet Insert Fasteners Stocked at Depot CB1200-I Pellet Insert Service And Maintenance Log Date of Service Performed By Description of Service CB1200-I Pellet Insert Warranty Policy CB1200-I Pellet Insert Contact Information