Fasteners, Stocked at Depot | Quadra-Fire CB1200I, CB1200MI-MBK

CB1200-I Pellet Insert

R

To order the entire assembly, order the top line part number only. HOW TO ORDER To order an individual part from an assembly, order the part(s) listed in

the indented portion.

Item	Description	Comments	Part Number
		FASTENERS

Stocked at Depot

	Avk Rivnut Repair Kit	1/4-20 & 3/8-16 Rivnut Tools	RIVNUT-REPAIR	Y
	Nut, Keps Lock, 8-32	Qty: 40	226-0060/40	Y
	Nut, Ser Flange Small 1/4-20	Qty: 24	226-0130/24	Y
	Screw, Pan Head Philips 8-32 X 3/8	Qty: 40	225-0500/40	Y

	Screw, Pan Head Philips 10-32 X	Qty: 40	21799A/40	Y
	3/8	Qty: 40	21799A/40	Y
	3/8
	Screw, Sheet Metal #8 X 1/2 S-Grip	Qty: 40	12460/40	Y

	Screw, Machine Screw 1/4-20X5/8	Qty: 24	220-0440/24	Y
	Washer, 1/4 Sae	Qty: 24	28758/24	Y

Page 48

7014-188B

February 3, 2010

Image 48

Quadra-Fire CB1200I, CB1200MI-MBK owner manual Fasteners, Stocked at Depot

Contents

CB1200MI-MBK Hot glass will cause burns CB1200-I Pellet Insert Welcome to the Quadra-Fire Family Table of Contents Appliance Certification BTU & Efficiency Specifications Glass SpecificationsListing and Code Approvals Mobile Home Approved Design, Installation & Location Consider- ations Appliance Location CB1200-I Pellet Insert Locating Your Appliance & Chimney Negative PressureThermostat Location Draft CB1200-I Pellet Insert Fire Safety Tools And Supplies NeededInspect Appliance & Components and Pre-Use Check List 3Dimensions and Clearances Appliance Dimensions Rear Shroud Kit is Required for Built-In Installation Shown with Rear Vent and Optional Outside AirInch 0mm Clearance to Exposed Section and Face Trim Zero Clearance Installations Non-Zero Clearance InstallationsFloor Protection Inches Millimeters Thermal Conductivity k value Thermal Resistance R valueConverting k to R Converting R to k Altering the Factory-Built Fireplace S629M, Standard for 650oC FACTORY-BUILT Chimneys Vent Information Chimney and Exhaust ConnectionVenting Termination Requirements Pipe Selection Chart CB1200-I Pellet Insert Equivalent Feet of PipeExample of 3 Elbow-Rear Vent Termination Calculation Venting Systems Full Reline With Outside Air Horizontal CB1200-I Pellet Insert Full Reline With Outside Air Vertical Mobile Home Rear Shroud Installation 7Appliance Set-Up Rear Vent Installation Preparation Installing Rear ShroudFor Top Vent Installation Attaching Shroud to Hopper Body Adjustable Hopper Options Grille InstallationTo adjust hopper CB1200-I Pellet Insert Outside Air Kit Instructions Adjustable Hearth Support Size 9D x 45W, 2 to 10 Height Adjustment CB1200-I Pellet Insert Panel and Trim Set CB1200-I Pellet Insert Panel and Trim Set Cont’d Completed View CB1200-I Pellet Insert Optional Brick Set Installation Brick Clip Installation Thermostat Installation Top Log, LeftRight Front Log 8Operating Instructions Fuel Size, Material and StorageWood Pellets Shelled Field Corn Cont’d Shelled Field Corn CB1200-I Pellet Insert General Operating Information Before Your First FireStarting Your First Fire Thermostat Calls For Heat CB1200-I Pellet Insert Fire Characteristics Feed Rate Adjustment InstructionsIgnition Cycles CB1200-I Pellet Insert Frequently Asked Questions Issues Solutions Troubleshooting Symptom Troubleshooting Cont’d Symptom Possible Cause Corrective Action Troubleshooting Cont’d 10Proper Shutdown Procedure Quick Reference Maintenance ChartMaintaining & Servicing Your Appliance Types of Fuel Cleaning Firepot with Cleaning Rod & Firepot Clean-Out Tool Cleaning Ash PanCleaning the Hopper See Disposal of Ashes Frequency As needed Cleaning Heat Exchanger Chambers & Drop Tube Cleaning Beneath Heat ExchangerCleaning Exhaust Path Cleaning the Glass Cleaning Exhaust Blower Requires No Lubrication Door Gasket InspectionPreparing Firebox for Non-Burn Season Frequency Yearly CB1200-I Pellet Insert High Ash Fuel Content Maintenance Immediate Attention and Cleaning is Required Before removing the side frame. Use a pow Ered Phillips head screw driver to remove Screws Igniter Replacement Baffle Removal Reference Materials CB 200-I Pellet InsertComponent Function Vacuum Switch Wiring Harness See .1 belowThermostat Snap Disc #1 Convection Blower 125F CB1200-I Pellet Insert Component Locations Control Box CB1200-I Pellet Insert Exploded Drawing CB1200-I Pellet Insert Service Parts and Accessories Important this is Dated Information HOW to Order Stocked At Depot Description Comments Part Number DR-CB12-NL-B Stocked Description Comments Part Number CB1200-I Pellet Insert Fasteners Stocked at Depot CB1200-I Pellet Insert Service And Maintenance Log Date of Service Performed By Description of Service CB1200-I Pellet Insert Warranty Policy CB1200-I Pellet Insert Contact Information