Quadra-Fire CUMPGAP-PMH Appliance Inspection Routine, Glass Replacement, Fire Risk Injury Risk

R

Cumberland Gap Wood Stove

B.Appliance Inspection - Routine

•Frequency: Every 2 months at the same time the chim- ney and chimney connector are inspected.

•By: Homeowner

Check for:

•Cracks in glass

•Door handle - smooth cam operation

•Baffles are in correct placement

•Baffle for warpage

•Firebrick for cracks, broken or crumbly

•Door gasket. (Dollar bill test). Place a dollar bill between the stove and the door and then shut the door. If you can pull the dollar bill out, replace the door gasket.

•Glass frame for loose screws

C.Inspect Firebrick & Replacement Instructions

•Frequency: After each ash removal

•By: Homeowner

Replace the firebrick if they become crumbly and/or if there is a 1/4 inch (6.35mm) gap between the bricks.

The firebox is lined with firebrick, which has exceptional in- sulating properties. Do not use a grate; simply build a fire on the firebox floor. Do not operate appliance without firebrick.

Ensure that the firebricks are correctly positioned and that the firebox does not contain any broken brick prior to operat- ing the unit.

1.After the coals have completely cooled, remove all old brick and ash from unit and vacuum out firebox.

2.Remove new brick set from box and lay out to the diagram shown in the instructions that come with the replacement brick set

3.Lay bottom bricks in unit.

4.Install rear bricks on the top of the bottom bricks. Slide top of bricks under clip on back of firebox wall and push bottom of bricks back.

5.Install side bricks. Slide top of brick under clips on side of firebox and push the bottom of the brick until it is flush with the side of the unit.

Use Part #832-0550 when ordering individual brick. Provide brick dimension or copy the page in the Service Parts List showing the brick dia- gram, mark the desired brick and take it to your authorized dealer.

D. Glass Replacement

1.Ensure that the fire is out and the appliance is cool to the touch.

2.Protect a table or counter top with padding or towels. Protect your hands and wear gloves to prevent injury.

3.Remove the door with the broken glass by lifting the door up and off of the hinges.

4.Lay door face down on a table or counter making sure the door handle and fiber handle hangs over the edge so the door lays flat on a soft surface.

5.Remove the screws from each glass retainer and remove the glass. (If screws are difficult to remove, soak with penetrating oil first).

6.Center the glass with edges evenly overlapping the opening in the door, (i.e. same space top and bottom, left and right sides).

7.Replace the glass retainers. Be careful not to cross thread the screws.

8.Tighten each retainer just a few turns until each is secured. Check again for centering of glass in door frame. Continue to tighten each retainer alternately, a few turns at a time, until the glass is snug. DO NOT OVERTIGHTEN.

9.Replace the door on the appliance.

Quadra-Fire stoves are equipped with ceramic super heat-resistant glass, which can only be broken by impact or misuse.

Do not slam stove door or impact the glass. When closing door, make sure that logs do not protrude against the glass. Inspect glass regularly.

If you find a crack or break, immediately put the fire out and return the door to your dealer for replacement of glass before further use.

WARNING

Handle glass with care.

• Inspect the gasket to ensure it is

Glass undamaged.

Assembly

• Do NOT strike, slam or scratch glass.

• Do NOT operate appliance with glass

&door assembly removed.

•Do NOT operate with glass cracked, broken or scratched.

WARNING

Fire Risk.

Injury Risk.

•Use only glass specified in manual.

•DO NOT REPLACE with any other material.

Glass breakage will occur.

Page 34 7006-188G November 5, 2010