Manuals / Quadra-Fire / Household Appliance / Indoor Fireplace

Quadra-Fire QV32-A H1 H, Venting with Two 90 Elbows, Use SL D-Seriescomponents only, Natural Gas

Models: QV32-A QV36-A

1 42

Page 20


VENTING WITH TWO (2) 90o ELBOWS			NATURAL GAS
V (MIN.)		H + H1 (MAX.)
90o Elbow on Top		2 FT (610mm)
1 FT (305mm)		3 FT (914mm)
2 FT (610mm)		4 FT (1.22m)
3 FT (914mm)		6 FT (1.86m)
4 FT (1.22m)		8 FT (2.48m)
5 FT (1.52m)		16 FT (4.8m)
H + H1 MAX. = 16 FT (4.8m)	V + H + H1		MAX. = 40 FT (12.2m)

VENTING WITH TWO (2) 90o ELBOWS		PROPANE
V (MIN.)	H + H1 (MAX.)
90o Elbow on Top	NOT ALLOWED
1 FT (305mm)	2 FT (610mm)
2 FT (610mm)	4 FT (1.22m)
3 FT (914mm)	6 FT (1.86m)
4 FT (1.22m)	8 FT (2.48m)
5 FT (1.52m)	16 FT (4.8m)
H + H1 MAX. = 16 FT (4.8m)	V + H + H1 MAX. = 40 FT (12.2m)

H1

Note: There MUST be a 25% reduction in total H when using flex vent, except when using the simple up and out installation (see Figure 9).

Use SL D-Series components only.

Figure 15. Venting with Two 90° Elbows

Page 20

Image 20

Quadra-Fire QV32-A, QV36-A H1 H, Venting with Two 90 Elbows, Use SL D-Seriescomponents only, VENTING WITH TWO 2 90o ELBOWS

Contents

What to do if you smell gas Installers GuideModels QV32-ASAFETY AND WARNING INFORMATION PROHIBITEDTABLE OF CONTENTS 8 Log Set Assembly Service Parts4 1 5 ACCESSORIES / ACCESSOIRES Service Parts 8 Log Set AssemblyOn/Off Rocker Switch ACCESSORIES / ACCESSOIRESInstallation Codes High Altitude InstallationsApprovals and Codes Appliance CertificationPre-installPreparation Getting StartedIntroducing the Village Collection Gas Fireplaces ANY SUCH ACTION MAY POSSIBLY CAUSE A FIRE HAZARDFigure 1. Diagram of the QV36-A u Figure 2. Diagram of the QV-32-A ACCESSELECTRICAL ACCESS TOP STANDOFFSInstalling the Fireplace Constructing the Fireplace ChaseStep 1. Locating the Fireplace Clearance Requirementsu Figure 5. Framing Dimensions Step 2. Framing the FireplaceVENT HOLE85/8” 220mm 47 3/4 Step 3. Installing the Vent System Identifying Vent ComponentsD-SERIES SL D-SERIESFlex Vent STRAIGHT UP VERTICAL VENTINGUse SL D-Seriescomponents only Use D-Seriescomponents onlyUse SL D-Seriescomponents only Figure 12. Venting with One 90 ElbowFigure 13. Venting with One 90 Elbow Use D-Seriescomponents onlyUse D-Series components only Figure 14. Venting with Two 90 ElbowsH + H1 V FTH1 H Figure 15. Venting with Two 90 ElbowsUse SL D-Seriescomponents only VENTING WITH TWO 2 90o ELBOWSFigure 16. Venting with Two 90 Elbows HUse SL D-Seriescomponents only VENTING WITH TWO 2 90o ELBOWSUse D-Series components onlyFigure 17. Venting with Three 90 elbows H + H1H H1 Figure 18. Venting with three 90 elbowsUse SL D-Seriescomponents only VENTING WITH THREE 3 90o ELBOWSFigure 19. Venting with three 90 elbows Use SL D-Seriescomponents onlyVENTING WITH THREE 3 90o ELBOWS NATURAL GASH1 H Figure 20. Venting with Four 90 elbowsVENTING WITH FOUR 4 90 ELBOWS NATURAL AND PROPANE GASB. Installing Vent Components Venting Out the Rear Vent See FigureVenting Out the Top Vent WARNING FAILURE TO REMOVE INSULATION3. Install Support Brackets 4. Install FirestopsFigure 24. Installing Support Brackets 2. Continue Adding Vent ComponentsFigure 28. Ceiling Firestop Ceiling Side Figure 27. Hole & New Framing MembersFigure 29. Attic Firestop JOIST CEILING NAILS 4 REQUIRED CEILING FIRESTOPC. Vent Termination WARNING THE TERMINATION CAP MUST BEPOSITIONED SO THAT THE ARROW IS POINTING UP ROUND CAP TERMINATION PERFORATION CANNOT BEFigure 31. Vent Termination Minimum Clearances = AREA WHERE TERMINAL IS NOT PERMITTED= VENT TERMINAL X = AIR SUPPLY INLETnail Step 5. The Gas Control System Figure 33. Proper Positioning, Leveling, andSecuring of a Fireplace WARNING THIS UNIT IS NOT FOR USE WITH SOLID FUELStep 6. The Gas Supply Line Step 7. Gas Pressure RequirementsWARNING DO NOT USE AN OPEN FLAME TO CHECK FOR GAS LEAKSStep 8. Wiring the Fireplace Figure 36. Standing Pilot Ignition Wiring DiagramFor Standing Pilot Ignition Wiring Optional AccessoriesWARNING WHEN FINISHING THE FIREPLACE Refractory Kit Placement BRICK-291, BRICK-293Step 9. Finishing Figure 39. Sealant MaterialStep 10. Installing Trim, Logs and Ember Material Installing the TrimShutter Settings Figure 45. Glass AssemblyReview safety warnings and cautions Double-checkfor faulty componentsStep 11. Before Lighting the Fireplace Double-checkfor gas leaksAfter the Installation FOR YOUR SAFETY READ BEFORE LIGHTINGStep 12. Lighting the Appliance LIGHTING INSTRUCTIONS STANDING PILOT CONTROLSFireplace Maintenance Cleaning Glass DoorMaintaining and Servicing Your Fireplace Replacing old ember materialTroubleshooting SymptomPossible Cause Corrective ActionTroubleshooting continued SymptomPossible Cause Corrective ActionLifetime Warranty THREE-YEARWARRANTYONE-YEARWARRANTY CONDITIONS

VENTING WITH TWO (2) 90o ELBOWS

NATURAL GAS

H1

Figure 15. Venting with Two 90° Elbows