Manuals / Quadra-Fire / Household Appliance / Indoor Fireplace

Quadra-Fire QV32-A Wiring the Fireplace, Standing Pilot Ignition Wiring Diagram, Wall Switch

Models: QV32-A QV36-A

1 42

Download 42 pages 34.68 Kb

Page 34

Figure 36. Standing Pilot Ignition Wiring Diagram

3/16” PIGGYBACK CONNECTOR

TH

TP

GAS VALVE

THERMOCOUPLE

	BLACK S2
	ON
	OFF
WHITE T2	ON/OFF
WHITE T2	SWITCH
RED T1
THERMOPILE
	BLACK S1

REMOTE SWITCH

PIGTAIL

OPTIONAL WALL SWITCH, THERMOSTAT OR REMOTE

Figure 36. Standing Pilot Ignition Wiring Diagram

Step 8. Wiring the Fireplace

NOTE: Electrical wiring must be installed by a licensed electrician.

CAUTION: DISCONNECT REMOTE CONTROLS IF AB- SENT FOR EXTENDED TIME PERIODS. THIS WILL PRE- VENT ACCIDENTAL FIREPLACE OPERATION.

For Standing Pilot Ignition Wiring

Appliance Requirements

•This appliance DOES NOT require 110-120 VAC to operate.

!WARNING: DO NOT CONNECT 110-120 VAC TO THE GAS CONTROL VALVE OR WALL SWITCH OR THE APPLIANCE WILL MALFUNCTION AND THE VALVE WILL BE DESTROYED.

Optional Accessories

Optional fan and remote control kits require that 110-120 VAC be wired to the factory installed junction box before the fireplace is permanently installed.

Wall Switch

Position the wall switch in the desired position on a wall. Run a maximum of 25 feet (7.8 m) or less length of 18 A.W.G. minimum wire and connect it to the fireplace ON/ OFF switch pigtails.

CAUTION: LABEL ALL WIRES PRIOR TO DISCONNEC- TION WHEN SERVICING CONTROLS. WIRING ERRORS CAN CAUSE IMPROPER AND DANGEROUS OPERATION. VERIFY PROPER OPERATION AFTER SERVICING.

BLK

						VARIABLE SPEED CONTROL		NOTE: IF ANY OF THE ORIGINAL WIRE
								AS SUPPLIED WITH THE APPLIANCE
								MUST BE REPLACED, IT MUST BE
						BLK		REPLACED WITH TYPE 105OC RATED WIRE.
							JUNCTION BOX
							JUNCTION BOX

BLK

BLK

TEMPERATURE SENSOR SWITCH

BLK
	BLK
BLK
WHT	WHT
BLK
GROUND
GRN
BLK	WHT
110-120 VAC

BLOWER RECEPTACLE

BLOWER

JUNCTION BOX

TEMPERATURE SENSOR SWITCH

Figure 37. Fan Wiring Diagram

FAN

SPEED CONTROL

(RHEOSTAT)

34

Image 34

Quadra-Fire QV32-A manual Wiring the Fireplace, Standing Pilot Ignition Wiring Diagram, For Standing Pilot Ignition Wiring

Contents

Models What to do if you smell gasInstallers Guide QV32-ASAFETY AND WARNING INFORMATION PROHIBITEDTABLE OF CONTENTS 4 1 5 Service Parts8 Log Set Assembly ACCESSORIES / ACCESSOIRES Service Parts 8 Log Set AssemblyOn/Off Rocker Switch ACCESSORIES / ACCESSOIRESApprovals and Codes Installation CodesHigh Altitude Installations Appliance CertificationIntroducing the Village Collection Gas Fireplaces Pre-installPreparationGetting Started ANY SUCH ACTION MAY POSSIBLY CAUSE A FIRE HAZARDFigure 1. Diagram of the QV36-A ELECTRICAL ACCESS u Figure 2. Diagram of the QV-32-AACCESS TOP STANDOFFSStep 1. Locating the Fireplace Installing the FireplaceConstructing the Fireplace Chase Clearance RequirementsVENT u Figure 5. Framing DimensionsStep 2. Framing the Fireplace HOLE85/8” 220mm 47 3/4 D-SERIES Step 3. Installing the Vent SystemIdentifying Vent Components SL D-SERIESUse SL D-Seriescomponents only Flex VentSTRAIGHT UP VERTICAL VENTING Use D-Seriescomponents onlyFigure 13. Venting with One 90 Elbow Use SL D-Seriescomponents onlyFigure 12. Venting with One 90 Elbow Use D-Seriescomponents onlyH + H1 Use D-Series components onlyFigure 14. Venting with Two 90 Elbows V FTUse SL D-Seriescomponents only H1 HFigure 15. Venting with Two 90 Elbows VENTING WITH TWO 2 90o ELBOWSUse SL D-Seriescomponents only Figure 16. Venting with Two 90 ElbowsH VENTING WITH TWO 2 90o ELBOWSFigure 17. Venting with Three 90 elbows Use D-Seriescomponents only H + H1Use SL D-Seriescomponents only H H1Figure 18. Venting with three 90 elbows VENTING WITH THREE 3 90o ELBOWSVENTING WITH THREE 3 90o ELBOWS Figure 19. Venting with three 90 elbowsUse SL D-Seriescomponents only NATURAL GASVENTING WITH FOUR 4 90 ELBOWS H1 HFigure 20. Venting with Four 90 elbows NATURAL AND PROPANE GASVenting Out the Top Vent B. Installing Vent ComponentsVenting Out the Rear Vent See Figure WARNING FAILURE TO REMOVE INSULATIONFigure 24. Installing Support Brackets 3. Install Support Brackets4. Install Firestops 2. Continue Adding Vent ComponentsFigure 29. Attic Firestop Figure 28. Ceiling Firestop Ceiling SideFigure 27. Hole & New Framing Members JOIST CEILING NAILS 4 REQUIRED CEILING FIRESTOPPOSITIONED SO THAT THE ARROW IS POINTING UP C. Vent TerminationWARNING THE TERMINATION CAP MUST BE ROUND CAP TERMINATION PERFORATION CANNOT BE= VENT TERMINAL Figure 31. Vent Termination Minimum Clearances= AREA WHERE TERMINAL IS NOT PERMITTED X = AIR SUPPLY INLETnail Securing of a Fireplace Step 5. The Gas Control SystemFigure 33. Proper Positioning, Leveling, and WARNING THIS UNIT IS NOT FOR USE WITH SOLID FUELWARNING DO NOT USE AN OPEN FLAME Step 6. The Gas Supply LineStep 7. Gas Pressure Requirements TO CHECK FOR GAS LEAKSFor Standing Pilot Ignition Wiring Step 8. Wiring the FireplaceFigure 36. Standing Pilot Ignition Wiring Diagram Optional AccessoriesStep 9. Finishing WARNING WHEN FINISHING THE FIREPLACERefractory Kit Placement BRICK-291, BRICK-293 Figure 39. Sealant MaterialShutter Settings Step 10. Installing Trim, Logs and Ember MaterialInstalling the Trim Figure 45. Glass AssemblyStep 11. Before Lighting the Fireplace Review safety warnings and cautionsDouble-checkfor faulty components Double-checkfor gas leaksStep 12. Lighting the Appliance After the InstallationFOR YOUR SAFETY READ BEFORE LIGHTING LIGHTING INSTRUCTIONS STANDING PILOT CONTROLSMaintaining and Servicing Your Fireplace Fireplace MaintenanceCleaning Glass Door Replacing old ember materialPossible Cause TroubleshootingSymptom Corrective ActionPossible Cause Troubleshooting continuedSymptom Corrective ActionONE-YEARWARRANTY Lifetime WarrantyTHREE-YEARWARRANTY CONDITIONS