47 3/4 | Quadra-Fire QV36-A, QV32-A manual

6 1/2	6 3/8
	6 3/8
9 1/4
	6 3/8
6 5/8
SL-45D	6 5/8
	6 5/8
	SL-90D

6 1/2

9 5/8

9 5/8

SL-09D

SL-12/17D (SL12-17D)

SL-24D

SL-36D

SL-48D

8 3/4

12-17

23 3/4

35 3/4

47 3/4

17-24

		6 1/2
	11 3/4
		5 3/4
SL-17/24D		6 5/8
SL-17/24D	SL-12D
(SL17-24D)	SL-12D	SL-06D

SL-FLEX-10

120”

(3048mm)

SL-FLEX-2

SL-FLEX-5

	60”	24”
	(1524mm)
		(610mm)

SL-FLEX-3

36”

(914mm)

NOTE: PIPES OVERLAP 1-3/8 INCHES (34.93mm) AT EACH JOINT.

Figure 7. SL D-Series Direct Vent Component Specifications (4-inch inner pipe / 6 5/8-inch outer pipe)

15

Image 15

Quadra-Fire QV36-A, QV32-A manual 47 3/4

Contents

What to do if you smell gas Installers Guide Safety and Warning Information Table of Contents Service Parts Standing Pilot Ignition / D’ALLUMAGE PAR Veilleuse Accessories / Accessoires Log Set Assembly DF-36TS-BK Certification Installation CodesHigh Altitude Installations Appliance Certification Pre-install Preparation Introducing the Village Collection Gas FireplacesANY Such Action MAY Possibly Cause a Fire Hazard Diagram of the QV36-A Diagram of the QV-32-A Constructing the Fireplace Chase Locating the FireplaceClearance Requirements Framing the Fireplace Framing Dimensions DV-FLEX-10 47 3/4 Installing the Vent System Identifying Vent ComponentsVent System Approvals Straight UP Vertical Venting Use SL D-Series components onlyUse D-Series components only Use SL D-Series components only Venting with Two 90 Elbows Natural GAS MAX. = 16 FT 4.8m V + V1 + H MAX. = 40 FT 12.2m Venting with Three 90 elbows Venting with Three 3 90 o Elbows + H 1 MAX. = 16 FT 4.8m + V 1 + H + H Venting with Four 90 elbows SET of Collars YOU are Using could Cause a Fire Continue Adding Vent Components Adding Venting Components Install Support Brackets Ceiling Firestop Ceiling Side Minimum Trapezoid CAP Termination Vent TerminationPositioned SO That the Arrow is Pointing UP 191mm Vent Termination Minimum Clearances Minimum Height from Roof to Lowest Discharge Opening Positioning, Leveling, and Securing the Fireplace Gas Control SystemStanding Pilot Ignition System Pressure Gas Supply LineGas Pressure Requirements To Check for GAS Leaks Wall Switch Wiring the FireplaceFor Standing Pilot Ignition Wiring Appliance Requirements Optional Accessories Finishing Refractory Kit Placement BRICK-291, BRICK-293 Glass Specifications Installing Trim, Logs Ember Material Before Lighting the Fireplace Double-check for faulty components What to do if YOU Smell GAS After the InstallationLighting the Appliance Standing Pilot Ignition Important Turn OFF the GAS Before Servicing Your Fireplace Fireplace Maintenance Troubleshooting Be Placed in this Opening Lifetime Warranty