Manuals / Quadra-Fire / Household Appliance / Indoor Fireplace

Quadra-Fire QV36-A, QV32-A manual Table Of Contents

Models: QV32-A QV36-A

1 42

Download 42 pages 34.68 Kb

Page 3

TABLE OF CONTENTS
Safety and Warning Information		2
uService Parts Lists		4
Section 1: Approvals and Codes		8
Appliance Certification		8
Installation Codes		8
High Altitude Installations		8
Section 2: Getting Started		9
Introducing the Village Collection Gas Fireplaces		9
u Pre-installation Preparation		9
Section 3: Installing the Fireplace		12
Constructing the Fireplace Chase		12
u Step 1	Locating the Fireplace	12
Step 2	Framing the Fireplace	13
Step 3	Installing the Vent System	16
	A. Vent System Approvals	16
	B. Installing Vent Components	26
	u C. Vent Termination	29
Step 4	Positioning, Leveling, and
	Securing the Fireplace	32
Step 5	The Gas Control Systems	32
Step 6	The Gas Supply Line	33
Step 7	Gas Pressure Requirements	33
Step 8	Wiring the Fireplace	34
Step 9	Finishing	35
	Refractory Kit Placement	35
Step 10	Installing Trim, Logs, and Ember Material	36
	Installing the Trim	36
	Shutter Settings	36
	Placing the Ember Material	36
Step 11	Before Lighting the Fireplace	37
Step 12	Lighting the Appliance	38
After the Installation		38
Section 4: Maintaining and Servicing Your Fireplace		39
Section 5: Troubleshooting		40
Limited Lifetime Warranty		42
u = Contains updated information.

3

Image 3

Quadra-Fire QV36-A, QV32-A manual Table Of Contents

Contents

QV32-A What to do if you smell gasInstallers Guide ModelsPROHIBITED SAFETY AND WARNING INFORMATIONTABLE OF CONTENTS Service Parts 4 1 58 Log Set Assembly ACCESSORIES / ACCESSOIRES 8 Log Set Assembly Service PartsACCESSORIES / ACCESSOIRES On/Off Rocker SwitchAppliance Certification Installation CodesHigh Altitude Installations Approvals and CodesANY SUCH ACTION MAY POSSIBLY CAUSE A FIRE HAZARD Pre-installPreparationGetting Started Introducing the Village Collection Gas FireplacesFigure 1. Diagram of the QV36-A TOP STANDOFFS u Figure 2. Diagram of the QV-32-AACCESS ELECTRICAL ACCESSClearance Requirements Installing the FireplaceConstructing the Fireplace Chase Step 1. Locating the FireplaceHOLE u Figure 5. Framing DimensionsStep 2. Framing the Fireplace VENT85/8” 220mm 47 3/4 SL D-SERIES Step 3. Installing the Vent SystemIdentifying Vent Components D-SERIESUse D-Seriescomponents only Flex VentSTRAIGHT UP VERTICAL VENTING Use SL D-Seriescomponents onlyUse D-Seriescomponents only Use SL D-Seriescomponents onlyFigure 12. Venting with One 90 Elbow Figure 13. Venting with One 90 ElbowV FT Use D-Series components onlyFigure 14. Venting with Two 90 Elbows H + H1VENTING WITH TWO 2 90o ELBOWS H1 HFigure 15. Venting with Two 90 Elbows Use SL D-Seriescomponents onlyVENTING WITH TWO 2 90o ELBOWS Figure 16. Venting with Two 90 ElbowsH Use SL D-Seriescomponents onlyH + H1 Use D-Seriescomponents only Figure 17. Venting with Three 90 elbowsVENTING WITH THREE 3 90o ELBOWS H H1Figure 18. Venting with three 90 elbows Use SL D-Seriescomponents onlyNATURAL GAS Figure 19. Venting with three 90 elbowsUse SL D-Seriescomponents only VENTING WITH THREE 3 90o ELBOWSNATURAL AND PROPANE GAS H1 HFigure 20. Venting with Four 90 elbows VENTING WITH FOUR 4 90 ELBOWSWARNING FAILURE TO REMOVE INSULATION B. Installing Vent ComponentsVenting Out the Rear Vent See Figure Venting Out the Top Vent2. Continue Adding Vent Components 3. Install Support Brackets4. Install Firestops Figure 24. Installing Support BracketsJOIST CEILING NAILS 4 REQUIRED CEILING FIRESTOP Figure 28. Ceiling Firestop Ceiling SideFigure 27. Hole & New Framing Members Figure 29. Attic FirestopROUND CAP TERMINATION PERFORATION CANNOT BE C. Vent TerminationWARNING THE TERMINATION CAP MUST BE POSITIONED SO THAT THE ARROW IS POINTING UPX = AIR SUPPLY INLET Figure 31. Vent Termination Minimum Clearances= AREA WHERE TERMINAL IS NOT PERMITTED = VENT TERMINALnail WARNING THIS UNIT IS NOT FOR USE WITH SOLID FUEL Step 5. The Gas Control SystemFigure 33. Proper Positioning, Leveling, and Securing of a FireplaceTO CHECK FOR GAS LEAKS Step 6. The Gas Supply LineStep 7. Gas Pressure Requirements WARNING DO NOT USE AN OPEN FLAMEOptional Accessories Step 8. Wiring the FireplaceFigure 36. Standing Pilot Ignition Wiring Diagram For Standing Pilot Ignition WiringFigure 39. Sealant Material WARNING WHEN FINISHING THE FIREPLACERefractory Kit Placement BRICK-291, BRICK-293 Step 9. FinishingFigure 45. Glass Assembly Step 10. Installing Trim, Logs and Ember MaterialInstalling the Trim Shutter SettingsDouble-checkfor gas leaks Review safety warnings and cautionsDouble-checkfor faulty components Step 11. Before Lighting the FireplaceLIGHTING INSTRUCTIONS STANDING PILOT CONTROLS After the InstallationFOR YOUR SAFETY READ BEFORE LIGHTING Step 12. Lighting the ApplianceReplacing old ember material Fireplace MaintenanceCleaning Glass Door Maintaining and Servicing Your FireplaceCorrective Action TroubleshootingSymptom Possible CauseCorrective Action Troubleshooting continuedSymptom Possible CauseCONDITIONS Lifetime WarrantyTHREE-YEARWARRANTY ONE-YEARWARRANTY