Venting with Two 90 Elbows | Quadra-Fire QV36-A, QV32-A guide

V	H	H + H1
1' MIN. (305 mm)	2' MAX. (610 mm)	4' MAX. (1.22m)
2' MIN. (610 mm)	4' MAX. (1.22 m)	8' MAX. (2.4m)
3' MIN. (914 mm)	6' MAX. (1.86 m)	12' MAX. (3.6m)
4' MIN. (1.22 m)	8' MAX. (2.48 m)	16' MAX. (4.8m)
V+H+H1 = 40' MAX. (12.4 m) H = 8' MAX. (2.48 m)		H+H1 = 16' MAX. (4.8m)

H1

V

Use D-Series

components only.

H

V (FT)	H + H1 (FT)
1' MIN. (305 mm)	2' MAX. (610 mm)
2' MIN. (610 mm)	4' MAX. (1.22 m)
3' MIN. (914 mm)	6' MAX. (1.86 m)
4' MIN. (1.22 m)	8' MAX. (2.48 m)
	H + H1= 8' MAX. (2.48 m)

V + H + H1= 40' (12.2m) MAX.

Note: There MUST be a 25% reduction in total H when using flex vent, except when using the simple up and out installation (see Figure 9).

V

H

H1

Figure 14. Venting with Two 90° Elbows

19

Image 19

Quadra-Fire QV36-A, QV32-A manual Venting with Two 90 Elbows

Contents

What to do if you smell gas Installers Guide Safety and Warning Information Table of Contents Service Parts Standing Pilot Ignition / D’ALLUMAGE PAR Veilleuse Accessories / Accessoires Log Set Assembly DF-36TS-BK Certification Installation CodesHigh Altitude Installations Appliance Certification Introducing the Village Collection Gas Fireplaces Pre-install PreparationANY Such Action MAY Possibly Cause a Fire Hazard Diagram of the QV36-A Diagram of the QV-32-A Locating the Fireplace Constructing the Fireplace ChaseClearance Requirements Framing the Fireplace Framing Dimensions DV-FLEX-10 47 3/4 Identifying Vent Components Installing the Vent SystemVent System Approvals Use SL D-Series components only Straight UP Vertical VentingUse D-Series components only Use SL D-Series components only Venting with Two 90 Elbows Natural GAS MAX. = 16 FT 4.8m V + V1 + H MAX. = 40 FT 12.2m Venting with Three 90 elbows Venting with Three 3 90 o Elbows + H 1 MAX. = 16 FT 4.8m + V 1 + H + H Venting with Four 90 elbows SET of Collars YOU are Using could Cause a Fire Continue Adding Vent Components Adding Venting Components Install Support Brackets Ceiling Firestop Ceiling Side Minimum Trapezoid CAP Termination Vent TerminationPositioned SO That the Arrow is Pointing UP 191mm Vent Termination Minimum Clearances Minimum Height from Roof to Lowest Discharge Opening Gas Control System Positioning, Leveling, and Securing the FireplaceStanding Pilot Ignition System Pressure Gas Supply LineGas Pressure Requirements To Check for GAS Leaks Wall Switch Wiring the FireplaceFor Standing Pilot Ignition Wiring Appliance Requirements Optional Accessories Finishing Refractory Kit Placement BRICK-291, BRICK-293 Glass Specifications Installing Trim, Logs Ember Material Before Lighting the Fireplace Double-check for faulty components What to do if YOU Smell GAS After the InstallationLighting the Appliance Standing Pilot Ignition Important Turn OFF the GAS Before Servicing Your Fireplace Fireplace Maintenance Troubleshooting Be Placed in this Opening Lifetime Warranty