Manuals / Regency / Household Appliance / Indoor Fireplace

Regency P33-LP3, P33-NG3 Bay Louvers, Flush Louver Top Heat Shield, Bay Louver Top Heat Shield

Models: P33-NG3 P33-LP3

1 48

Download 48 pages 9.74 Kb

Page 30

BAY LOUVERS

INSTALLATION

BAY LOUVERS

1)Remove ﬂ ush louver top heat shield by removing the 4 screws.

4)Install bottom louver by sliding the two bracket clips into the brackets located underneath the bay door. Secure with 1 screw into each Bottom Louver Mounting Bracket as per diagram below. Use the bottom hole in the bracket.

5)Slide the valve extension knobs onto the valve knobs. Match the correct ext. knob with the valve knob.

Flush Louver Top

Heat Shield

2) Install the bay louver top heat shield and secure with 4 screws.

6) Open the bottom louver. Pull the Burner ON/OFF control box from inside the bottom of the ﬁ replace and position the slots in the bracket over the 2 screws on the left side of the bottom louver. Push down to lock into place. Tighten the screws.

Bay Louver Top

Heat Shield

3)Install top louver by sliding the two bracket clips into the brackets located on top of the bay door. See below. The ﬁ tted louver leaves a small gap between faceplate bottom and louver top.

Burner ON/OFF

control box

Regency P33-3 Zero Clearance Direct Vent Gas Fireplace

Image 30

Regency P33-LP3, P33-NG3 Bay Louvers, Flush Louver Top Heat Shield, Bay Louver Top Heat Shield, Burner ON/OFF control box

Contents

Direct Vent Gas Fireplace Installation ManualP33-3Zero Clearance OwnersTo the New Owner Parts List Safety LabelInstallation P33-3ZERO CLEARANCE DIRECT VENT GAS FIREPLACESAFETY LABEL SAVE THESE INSTRUCTIONS INSTALLATIONGENERAL SAFETY INFORMATION BEFORE YOU STARTNote For vent terminations see page Diagram INSTALLATION CHECKLISTUNIT DIMENSIONS LOCATING YOUR GAS STOVEclearances are not adhered to CLEARANCESCOMBUSTIBLE MANTELSMANTEL LEG CLEARANCES Fire hazard is an extreme risk if theseSimpson Dura-VentMinimum Clearances FRAMING AND FINISHINGRear Termination Vertical Termination orVENTING INTRODUCTION UNIT ASSEMBLY PRIOR TO INSTALLATIONTop Standoff Assembly Top Facing Support & Side Nailing StripsTERMINATION LOCATIONS Area where terminal is not permitedVENT EXTERIORMinimum Simpson Dura-Vent Center-Line REGENCY DIRECT VENT SYSTEM FLEXHORIZONTAL TERMINATIONS ONLY Minimum Flex Kit Center-LineINSTALLATION PROCEDURES Horizontal or Vertical Terminations Flat Wall InstallationRIGID PIPE VENTING SYSTEMS nation CapsSimpson Dura-Vent RIGID PIPE VENTING COMPONENTS LISTDescription SelkirkPropane & Natural Gas Vent must be supported at offsetsMaintain clearances to combustibles The P33-3is approved for a maximum 40 ft. straight vertical, with rigid pipe vent systems for Propane and Natural Gas Vent must be supported at offsetsMaintain clearances to combustibles Minimum Flex Kit Center-Line REGENCY DIRECT VENT SYSTEM FLEXMinimum Simpson Dura-Vent Center-Line Maintain clearances to combustiblesHorizontal Venting with Two 2 90o Elbows Horizontal Venting with Two 2 90o ElbowsHorizontal Venting with Three 3 90o Elbows OptionVertical Venting with Two 2 90o Elbows Horizontal Venting with Three 3 90o ElbowsVertical Venting with Two 2 90o Elbows OptionOption Vertical Venting with Three 3 90o ElbowsVertical Venting with Three 3 90o Elbows H + H1VERTICAL TERMINATION WITH CO-LINEARFLEX SYSTEM with Co-linearFlex System for both The shaded area in the diagrams show theVenting Arrangements - Vertical Terminations Residential & Manufactured HomesDiagram HORIZONTAL INSTALLATIONSDiagram Below Grade Snorkel InstallationDiagram GAS LINE INSTALLATIONDiagram DiagramHIGH ELEVATION PILOT ADJUSTMENTGAS PIPE PRESSURE TESTING S.I.T. VALVE DESCRIPTIONIF IN DOUBT DO NOT DO THIS CONVERSION for P33-3using SIT 820 NOVA Gas ValveAssembly to the left and lift out Conversion Kit ContainsNote The logs must not be in the unit LOG SET INSTALLATIONOPTIONAL BRICK PANELS NotchDiagram Diagram Place rockwool in these 2 locationsDiagram STANDARD FLUSH DOORFLUSH LOUVERS DiagramClip installed on right side DOUBLE SCREEN DOORBay Louver Top Heat Shield BAY LOUVERSFlush Louver Top Heat Shield Burner ON/OFF control boxCut-Out Oblong Hole Cut-Out Top Flange Bottom FULL SCREEN FRONTBackside of FullFlange Screen Door Frame Shown Cut-OutsLeft Side of Bottom Grill Screen Door Hinge Location Bottom GrillHinge Top GrillDo not wire millivolt wall switch wire OPTIONAL WALL SWITCHREMOTE CONTROL to 120V wireWIRING DIAGRAM Diagram INSTALLING THE OPTIONAL FAN1 Shut the power off Diagram 3 Use the clip & hook on the side ofOPERATING INSTRUCTIONS COPY OF THE LIGHTING PLATE INSTRUCTIONSAERATION ADJUSTMENT LIGHTING PROCEDURESHUTDOWN PROCEDURE CLEAN THE GLASS WHILE IT IS HOTGeneral Vent Maintenance MAINTENANCE INSTRUCTIONSLOG REPLACEMENT NORMAL OPERATING SOUNDS OF GAS APPLIANCESGLASS GASKET Flush Glass ReplacementTHERMOPILE THERMOCOUPLE DOOR GLASSREMOVING VALVE INSTALLING VALVEDiagram 3 Lift out Valve Tray Assembly 1Shut off the gas supplyMain Assembly DescriptionDescription PARTS LIST Burner & Log Assembly Part DescriptionFlush Front & Louvers DescriptionDescription Bay Front & Louvers DescriptionPage WARRANTY ConditionsExclusions door