Installation | Regency P33-LP3, P33-NG3 instruction

INSTALLATION

The P33-3 is approved for a maximum 40 ft. straight vertical, with rigid pipe vent systems for Propane and Natural Gas.

The shaded area in the diagram shows all allowable combinations of straight vertical and offset to vertical terminations with rigid pipe vent systems for Propane and Natural Gas. Maximum two 45o elbows allowed.

•Vent must be supported at offsets.

•Firestops are required at each ﬂoor level and whenever passing through a wall.

•Maintain clearances to combustibles.

Regency P33-3 Zero Clearance Direct Vent Gas Fireplace

Image 16

Regency P33-LP3, P33-NG3 installation manual Installation

Contents

P33-3 Zero Clearance Information for MOBILE/MANUFACTURED Homes After First Sale To the New Owner Table of Contents Safety Label Installation General Safety InformationSave These Instructions Before YOU Start Installation Checklist Unit DimensionsLocating Your GAS Stove Duct System Option Clearancescombustible Mantels Mantel LEG ClearancesClearances are not adhered to Fire hazard is an extreme risk if these Framing and Finishing Rear TerminationSimpson Dura-Vent Minimum Clearances Vertical Termination or Vertical Rise with Horizontal Unit Assembly Prior to Installation Top Standoff AssemblyVenting Introduction Top Facing Support Side Nailing Strips Vent Vent terminal Air supply outlet Regency Direct Vent System Flex Horizontal Terminations only Installation Procedures For Regency Direct Vent System Flex Flat Wall Installation Rigid Pipe Venting SystemsMax. Wall Vent Length Thickness inches Required inches Description Simpson Dura-Vent Selkirk Rigid Pipe Venting Components ListDirect VentGS R Direct-Temp TM Rigid Pipe Venting Arrangements Vertical Terminations Propane & Natural Gas Installation Rigid Pipe Venting Arrangements Horizontal Terminations Regency Direct Vent System Flex Horizontal Venting with Three 3 90o Elbows Horizontal Venting with Two 2 90o ElbowsOption + H1 Vertical Venting with Two 2 90o Elbows Option + V1 H + H1Option + V1 With these options, max. total Vertical Venting with Three 3 90o Elbows Vertical Termination With CO-LINEAR Flex System Required PartsDescription Alternate Approved Caps Installation Below Grade Snorkel Installation Horizontal InstallationsSnorkel Terminations GAS Line Installation Vertical Termination Pilot Adjustment GAS Pipe Pressure TestingHigh Elevation T. Valve Description Conversion Kit Contains LOG SET Installation Optional Brick PanelsNotch BracketBracket Standard Flush Door Optional Flush TrimCutout 5th Grate Tab Flush Louvers Double Screen DoorOptional BAY Door Bay louvers Must be used With the Bay glass option BAY Louvers Flush Louver Top Heat ShieldBay Louver Top Heat Shield Burner ON/OFF Control box Cut-Out Oblong Hole Top Flange Bottom Full Screen FrontCut-Outs Hinge Location Bottom Grill Top Grill Optional Wall Switch Thermostat Wire Table Wiring Diagram Do not cut the ground terminal off under any circumstances Installing the Optional FAN Shut the power offDiagram Secure left side with 2 screws Secure the 2 boxes together With one screw Operating Instructions Copy of the Lighting Plate Instructions Lighting Procedure Shutdown ProcedureAeration Adjustment Operating Instructions Maintenance Maintenance InstructionsLOG Replacement Normal Operating Sounds GAS Appliances Flush Glass Replacement Thermopile ThermocoupleGlass Gasket Door Glass Installing Valve Diagram 3 Lift out Valve Tray AssemblyRemoving Valve Shut off the gas supply Parts List Description Parts List Burner & Log Assembly Part Description Flush Front & Louvers Bay Front & Louvers Regency P33-3 Zero Clearance Direct Vent Gas Fireplace Warranty Conditions Installer Please complete the following information