Manuals / Regency / Household Appliance / Indoor Fireplace

Regency P42-LP4 Vent must be supported at offsets, Note Must use optional rigid pipe adaptor

Models: P42-LP4 P42-NG4

1 48

Download 48 pages 16.72 Kb

Page 17

•Vent must be supported at offsets

INSTALLATION

RIGID PIPE VENTING ARRANGEMENTS - VERTICAL TERMINATIONS

(Propane & Natural Gas)

The shaded area in the diagram shows all allowable combinations of straight vertical and offset to vertical terminations with rigid pipe vent systems for Propane and Natural Gas.

Maximum two 45o elbows allowed.

•Vent restrictor #6 must be used in shaded area in diagram below.

•Vent must be supported at offsets

The P42 is approved for a 37 ft. (11.3m) straight vertical, including a 20" (0.5m) horizontal offset using two 90o elbow (two 45o elbows equal one 90o elbow) with rigid pipe vent systems for Propane and Natural Gas, as per the diagram to the right.

•Vent restrictor #6 is required for terminations in shaded area.

•Vent must be supported at offsets.

Note: Must use optional rigid pipe adaptor
when using rigid vent systems (Part
# 510-994).
Note: Regency® Direct Vent System (Flex)
is only approved for horizontal
terminations.
Diagram 1	Diagram 2
Regency® P42-4 Zero Clearance Direct Vent Gas Fireplace	17

Image 17

Regency P42-LP4, P42-NG4 Vent must be supported at offsets, Note Must use optional rigid pipe adaptor, terminations

Contents

Owners Installation ManualP42 Gas Fireplace To the New Owner CongratulationsINSTALLATION TABLE OF CONTENTSPARTS LIST WARRANTYCOPY OF SAFETY DECAL FOR P42 SAFETY LABELMA Code - CO Detector REQUIREMENTS5.08 Modifications to NFPA-54,Chapter OBSTRUCTIONSGENERAL SAFETY INFORMATION INSTALLATIONINSTALLATION CHECKLIST IMPORTANT MESSAGE SAVE THESE INSTRUCTIONSDiagram UNIT SPECIFICATIONSMANUFACTURED MOBILE HOME ADDITIONAL REQUIREMENTS LOCATING YOUR GAS FIREPLACEMANTEL LEG CLEARANCES CLEARANCESMANTELSClearance to Combustibles from Minimum Clearance from Louver toDiagram TOP ASSEMBLY & NAILING STRIPSDiagram Diagram DiagramEXTERIOR VENT TERMINATION REQUIREMENTS 4 102mm Wall Thimble 2 pcAstroCap dia. flue pipe4” X 6-5/8”RIGID PIPE CROSS REFERENCE CHART Offset Pipe Selection 4” x 6-5/8”Rigid Pipe Cross Reference Chart ContHorizontal or Vertical Terminations RIGID PIPE VENTINGVertical Terminal Storm Collar Flashing 943 or 943SA vent guard may be required, check local codes when using rigid pipe venting systemsMinimum height requirementHorizontal vent must be supported every 3 feet For All Horizontal Terminationsa wall 6-5/8outer diameterVent must be supported at offsets when using rigid vent systems PartVent must be supported at offsets Note Must use optional rigid pipe adaptorDiagram DiagramNo Vent restrictor is required Vent must be supported at offsetsRequired Parts VERTICAL TERMINATION WITH CO-LINEARFLEX SYSTEMVENTING ARRANGEMENTS - VERTICAL TERMINATIONS Diagram DiagramDiagram Diagram 3aDiagram DiagramDiagram DiagramOffset Chart INSTALLATION PROCEDURESDiagram for Regency Direct Vent System FlexGAS PIPE PRESSURE TESTING GAS LINE INSTALLATIONHIGH ELEVATION System DataAERATION ADJUSTMENTBRICK PANELS Tab TabPROPANE LOG SET INSTALLATIONNATURAL GAS Diagram DiagramDiagram DiagramBAY LOUVERS OPTIONAL BAY DOOROptional Bay Trim The Bay louvers MUSTbe usedFULL SCREEN DOORS 3Full Screen Door Frame InstallationBackside of Full Screen Door Frame Shown Inside Top of Outer Frame Screw Screw ScrewBackside of Full Screen Door Frame Shown Hinge Location Bottom GrillRight Side of Bottom Grill Bottom Flange Inner Cut-OutsTop Grill HingeScreen Door WIRING DIAGRAMS INSTALLATION LIGHTING PROCEDURE Optional WALL SWITCHREMOTE CONTROL Do not wire millivolt wall switch wireCOPY OF THE LIGHTING PLATE INSTRUCTIONS FOR YOUR SAFETY READ BEFORE LIGHTINGDO NOT REMOVE THIS INSTRUCTION PLATE LIGHTING INSTRUCTIONSMAINTENANCE INSTRUCTIONS SHUTDOWN PROCEDUREFIRST FIRE NORMAL OPERATING SOUNDS OF GAS APPLIANCESLOG REPLACEMENT GOLD-PLATEDGLASS LOUVERS REPLACEMENTBay Glass Replacement Flush Glass ReplacementREMOVING THE FAN 1Shut the power offREPLACING THE FAN REMOVING VALVEINSTALLING VALVE Description PARTS LISTP42 MAIN ASSEMBLY Description P42 BURNER & LOG ASSEMBLYDescription P42 FLUSH DOOR & LOUVERSDescription P42 BAY FRONT & LOUVERSDescription Page Page Page Exclusions WARRANTYConditions thoroughly before it leaves our door