About V-LINK

V-LINK settings

Parameter

Range

Explanation

 

 

 

Note Tx Ch

1–16

MIDI channel that will switch Edirol DV-7PR clips/palettes and will control dissolve time.

Clip 1 Note No.

0(C-1)–127(G9)

Note number (velocity pad) that corresponds to Edirol DV-7PR clip 1

 

 

If this is set to 59 (B3), velocity pads 1–16 will correspond to clips 1–16.

Play Speed Ctrl

0.0–1.0–2.0, 0.5–1.0–2.0,

Range of video playback speed

 

0.0–1.0–4.0, 0.5–1.0–4.0,

The three values are the playback speeds (multiples of normal speed) at the negative,

 

0.0–1.0–8.0, 0.5–1.0–8.0,

center, and positive positions of the turntable emulation slider.

 

0.0–1.0–16.0, 0.5–1.0–16.0,

 

 

0.0–1.0–32.0, 0.5–1.0–32.0,

 

 

0.0–2.0–4.0, 0.0–4.0–8.0,

 

 

0.0–8.0–16.0, 0.0–16.0–32.0,

 

 

-2.0–1.0–4.0, -6.0–1.0–8.0

 

Dissolve Time

OFF, CC1, CC5, CC7, CC10,

Control change number that controls the dissolve time (time over which the image switch-

 

CC11, CC71–74, CC91–93,

es)

 

Channel Aftertouch

 

Ctrl Tx Ch

1–16

MIDI channel that will control the Edirol DV-7PR color Cb/Cr, brightness, and video effect

 

 

switching

Color Cb Ctrl

OFF, CC1, CC5, CC7, CC10,

Control change number that controls the Cb color of the image

Color Cr Ctrl

CC11, CC71–74, CC91–93,

Control change number that controls the Cr color of the image

Brightness Ctrl

Channel Aftertouch

Control change number that controls the brightness of the image

VFX1–4 Ctrl

 

Control change number that controls the video effect

 

 

* VFX2–4 are not supported by the Edirol DV-7PR.

Fade Ctrl

 

Control change number that controls the output fade

PAD MODE

CLIP, PALETTE

Selects whether the velocity pads will switch clips or palettes.

 

 

Press [F1 (Clip mode)]: switch clips

 

 

Press [F2 (Palette)]: switch palettes

Local Sw

OFF, ON

Specifies whether the internal sound generator is disconnected (OFF) from the velocity

 

 

pads, or not (OFF).

Clip filter

(OFF), (ON)

Enable/disable switching for each clip

(check boxes 1–32)

 

Clips that are checked can be switched (see explanatory box below)

Using the Clip Filter

For example, suppose that of the rhythm set you input in the part used for V-LINK (i.e., the part of the same number as the Note Tx Channel), you want only the kick and snare to switch clips. In this case, check only the clips that correspond to the note numbers of the kick and snare. The clips will switch when the kick or snare plays.

Resetting the image

[F3

(Clip Reset)]

Turn off the image (solid black).

[F4

(All Reset)]

The effect applied to the image will be reset,

 

 

and brightness, color difference, etc. will all

 

 

return to the default value.

*For details on clips/palettes, dissolve time, color difference signals (Cb/ Cr), refer to the Edirol DV-7PR manual.

The MC-909 does not support the Edirol DV-7PR’s dual stream mode.

V-LINK

139

Page 139
Image 139
Roland MC-909 owner manual Link settings, Resetting the image, About V-LINK, Using the Clip Filter, 139