Quick Setup, Installation specialist | Runco CL-610 instruction

Installation

3.2

Quick Setup

Table 3-1gives a quick overview of the CL-610 installation process. The sections following this one provide detailed instructions.

	Note		Installation should be performed by a qualified custom video
	Note		installation specialist.
Table 3-1. Installation Overview

Step			Procedure	For Details, Refer to
Step			Procedure	page...
				page...

1		Choose a location for the projector		15

2		Mount the projector		18

3		Connect signal sources to the CL-610		19

4		Connect external controller to RS-232 port (optional)		23

5		Connect 12-volt trigger output to retractable screen or		24
5		other, +12-volt trigger-activated equipment (optional)
		other, +12-volt trigger-activated equipment (optional)

6		Apply power to the projector		24

7		Change the OSD Language (optional)		25

8		For rear-screen and/or ceiling-mount installations, select		25
8		the proper picture orientation
		the proper picture orientation

9		Primary lens adjustments: projected image size (zoom) and		25
9		focus
		focus

10		Install CineWide anamorphic lens		26
10		(CL-610/CineWide and CL-610LT/CineWide only)
		(CL-610/CineWide and CL-610LT/CineWide only)

11		CineWide lens adjustments: position, angle, geometry and		27
11		focus
		focus

		Projector calibration: adjust the following for each input;		37 through 43
		save settings when finished:
		• Aspect ratio
12		• Brightness
12		• Contrast
		• Contrast
		• Color level
		• Tint
		• Input position

14	Runco CL-610 Series Owner’s Operating Manual

Image 26

Runco CL-610 manual Quick Setup, Installation specialist, Step Procedure For Details, Refer to

Contents

CL-610 Series Page TWO Year Limited Warranty Effective Warranty Date Runco INTERNATIONAL, INC Safety Precautions Table of Contents Maintenance and Troubleshooting Operation CL-610 Table of Contents List of Figures List of Figures Xii About This Manual Carriage return must be used after each command or stringIntroduction Target Audience Significance. They also provide supplemental information Using This ManualCertain features Degrade performance or cause a malfunction Description, Features and Benefits Format screen Optional Accessories Front/Side/Top View Controls and FunctionsCL-610 at a Glance Intake Vent Front IR Sensor Projection Lens Connector PanelAC Power Switch Rear/Side/Bottom View Status Indicators Lens Controls Lamp LED CL-610 Connector PanelPOWER/STANDBY LED Indicates power status as follows Temp LED RS-232 Control Port VideoComposite Video Input On / OFF CL-610 Remote ControlLight Hdmi VIDRgbhd Info ISF DAY MEM1ISF Night Fact Installation Remote Control Step Procedure For Details, Refer to Quick SetupInstallation specialist Ambient Light Installation ConsiderationsInstallation Type Lens Throw Range Throw Ratio Inches, withProjector Model Screen Folded Optics Vertical and HorizontalPosition Mounting the CL-610 Connections to the CL-610 Connector Panel AccessConnecting Source Components to the CL-610 CL-610 supports the following computer resolutions 1024x768, 800x600 Progressive Component Video Connections DTV Source DVD Player, VCR Satellite Receiver Etc RS-232 Controller Connection Theater Equipment Connecting 12-voltTrigger Output to External Zoom and Focus Adjustments Installing and Adjusting the CineWide Anamorphic Lens Height Y Adjustment Adjusting the Anamorphic Lens Tip Selecting Video Memory Using Picture-In-Picture and Picture-By-Picture PIP/PBPOperation Selecting an Aspect Ratio Turning Off the Power Using the On-Screen Menus RGB-HD ISF Enter or Picture AdjustmentMain Menu Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Below is set to Aspect Ratio You must enter a passcode in order to enter the Set Up menuInternational Color Consortium ICC is a group of imaging Aspect Ratio Settings Remote Aspect Ratio Control Description Key Select Cinema to view To exit InstallationTakes effect immediately you do not need to press Enter Option Shift controls in the Set Up menu see Set Up You select that menu after turning on the projector Operation Order to change the secondary IR code Operation This menu should be used by ISF-certified technicians only Reset Picture AdjustISF Calibration When you change a setting, save the change to a preset Operation Maintenance and Troubleshooting Lamp Replacement Troubleshooting Tips Symptom Possible Causes Solution Symptom Maintenance and Troubleshooting Code Function Serial CommunicationsIs turned on or off Serial Communications Serial Commands Serial Communications Specifications CL-610 Specifications Power Requirements Home Theater Calibration SpecificationsIndustry-Standard Specifications Dimensions CL-610 Dimensions CL-610 Dimensions Specifications Runco CL-610 Series Owner’s Operating Manual Power-cycle the projector to see the change Page Runco CL-810 Owner’s Operating Manual