Runco CL-610 specs

Installation

3.10 Installing and Adjusting the CineWide Anamorphic Lens

If you are installing a CineWide-equipped projector, proceed as follows to install and adjust the anamorphic lens.

It is extremely important that the primary lens is properly

Note adjusted before you install the anamorphic lens. Ensure that the image from the primary lens is perfectly centered on the screen.

The Anamorphic lens mount kit consists of everything shown in Figure 3-10.If any items are missing or damaged, please contact your Runco dealer or Runco Customer Service at (800) 23RUNCO.

1 Anamorphic Lens

2 Mounting Bracket (2x)

3 Pitch Adjustment Screw,

4-40 x 5/16" (4x)

4 Washer (4x)

5 Y-Adjustment Screw, Phillips Pan-Head, 6-32 x 3/8" (4x)

6 Fender Washer (4x)

	Figure 3-10. Anamorphic Lens Mounting Assembly - Exploded View
Remove the Projector ➤	Loosen the small Phillips screw (directly below the lens) holding the jewelry in place. Then,
Front Jewelry	remove the jewelry.
Installing the Anamorphic ➤	1.	Use the Pitch Adjustment Screws (item #3) and Washers (item #6) to attach the
Lens		Mounting Brackets (item #2) to the Anamorphic Lens (item #1). (Do not fully tighten
		the screws yet.)
	2.	Use the four Y-Adjustment Screws (item #5) and Washers (item #4) to attach the
		Anamorphic Lens assembly to the front of the projector. (Again, do not fully tighten
		the screws yet.)

26	Runco CL-610 Series Owner’s Operating Manual

Image 38

Runco CL-610 manual Installing and Adjusting the CineWide Anamorphic Lens

Contents

CL-610 Series Page TWO Year Limited Warranty Effective Warranty Date Runco INTERNATIONAL, INC Safety Precautions Table of Contents Maintenance and Troubleshooting Operation CL-610 Table of Contents List of Figures List of Figures Xii About This Manual Carriage return must be used after each command or stringIntroduction Target Audience Significance. They also provide supplemental information Using This ManualCertain features Degrade performance or cause a malfunction Description, Features and Benefits Format screen Optional Accessories Front/Side/Top View Controls and FunctionsCL-610 at a Glance Intake Vent Front IR Sensor Projection Lens Connector PanelAC Power Switch Rear/Side/Bottom View Status Indicators Lens Controls Lamp LED CL-610 Connector PanelPOWER/STANDBY LED Indicates power status as follows Temp LED RS-232 Control Port VideoComposite Video Input On / OFF CL-610 Remote ControlLight Hdmi VIDRgbhd Info ISF DAY MEM1ISF Night Fact Installation Remote Control Step Procedure For Details, Refer to Quick SetupInstallation specialist Ambient Light Installation ConsiderationsInstallation Type Lens Throw Range Throw Ratio Inches, withProjector Model Screen Folded Optics Vertical and HorizontalPosition Mounting the CL-610 Connections to the CL-610 Connector Panel AccessConnecting Source Components to the CL-610 CL-610 supports the following computer resolutions 1024x768, 800x600 Progressive Component Video Connections DTV Source DVD Player, VCR Satellite Receiver Etc RS-232 Controller Connection Theater Equipment Connecting 12-voltTrigger Output to External Zoom and Focus Adjustments Installing and Adjusting the CineWide Anamorphic Lens Height Y Adjustment Adjusting the Anamorphic Lens Tip Selecting Video Memory Using Picture-In-Picture and Picture-By-Picture PIP/PBPOperation Selecting an Aspect Ratio Turning Off the Power Using the On-Screen Menus RGB-HD ISF Enter or Picture AdjustmentMain Menu Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Below is set to Aspect Ratio You must enter a passcode in order to enter the Set Up menuInternational Color Consortium ICC is a group of imaging Aspect Ratio Settings Remote Aspect Ratio Control Description Key Select Cinema to view To exit InstallationTakes effect immediately you do not need to press Enter Option Shift controls in the Set Up menu see Set Up You select that menu after turning on the projector Operation Order to change the secondary IR code Operation This menu should be used by ISF-certified technicians only Reset Picture AdjustISF Calibration When you change a setting, save the change to a preset Operation Maintenance and Troubleshooting Lamp Replacement Troubleshooting Tips Symptom Possible Causes Solution Symptom Maintenance and Troubleshooting Code Function Serial CommunicationsIs turned on or off Serial Communications Serial Commands Serial Communications Specifications CL-610 Specifications Power Requirements Home Theater Calibration SpecificationsIndustry-Standard Specifications Dimensions CL-610 Dimensions CL-610 Dimensions Specifications Runco CL-610 Series Owner’s Operating Manual Power-cycle the projector to see the change Page Runco CL-810 Owner’s Operating Manual