Runco runco super hdtv dtv video projector, dtv-992/992 ultra

Connections

Connecting a Component source.

(R-Y)Y(B-Y) analog input terminals with sync input or with sync on the luminance (Y) input. The projector detects automatically where the sync signal is located.

This device complies with part 15 of the FCC rules. Operation is subject to following two conditions (1). This device may not cause harmful inter- ference, and (2) this device must accept any interference received including interference that may cause undesired operation.

Comm Port	Port 3	R	G	B Comp/ VSYNC	VIDEO	Green=Oper.
Off On				HSYNC		Red=Stby

Power/Mains

Audio amplifier

VCR HDTV player

(R-Y)Y(B-Y)S or (R-Y)Ys(B-Y) input selection

a. With the RCU: Select “Component” in the Source Selection Menu

b. With the local keypad :

(to gain access to the local keypad, see ‘Local keypad’ in chapter ‘Location and function of con- trols’.)

-Press ADJUST key, the General access menu is displayed on the screen.

-Use the control disk to highlight 5.

-Press ENTER to select the highlighted source.

Connecting a Component source with Tri-level sync.

(R-Y)Y(B-Y) analog input terminals with Tri-level sync input or with Tri-level sync on the luminance input.

This device complies with part 15 of the FCC rules. Operation is subject to following two conditions (1). This device may not cause harmful inter- ference, and (2) this device must accept any interference received including interference that may cause undesired operation.

Comm Port	Port 3	R	G	B Comp/ VSYNC	VIDEO	Green=Oper.
Off On				HSYNC		Red=Stby

Power/Mains

Audio amplifier

VCR HDTV player

This device complies with part 15 of the FCC rules. Operation is subject to following two conditions (1). This device may not cause harmful inter- ference, and (2) this device must accept any interference received including interference that may cause undesired operation.

Comm Port	Port 3	R	G	B Comp/ VSYNC	VIDEO	Green=Oper.
Off On				HSYNC		Red=Stby

Power/Mains

Audio amplifier

VCR HDTV player

3-4

Image 15

Runco runco super hdtv dtv video projector manual Connecting a Component source, YYB-YS or R-YYsB-Y input selection

Contents

DTV-992/992 Ultra Page Table of Contents Table of Contents APP-3 APX-6 EYE-QTMDIAGNOSTICS Installation Instructions Safety Instructions Safety Instructions Location and Function of Controls Rear Panel TerminologyFront Panel Terminology Control panel terminology Local KeypadRCU control panel terminology IR Transmission Indicator Connections AC Power mains Cord ConnectionPower Check Switching On/Off Signal Input Connection to the Projector Start up with full white imagePort No Projector Input Press Digit Button RGB3S or RG3sB input selection Connecting a RGB Analog source with composite syncConnecting a RGB Analog source with Tri-level sync Rgbs or RGsB input selection Connecting a Component source Connecting a Component source with Tri-level syncYYB-YS or R-YYsB-Y input selection Remote control YYB-Y3S or R-YY3sB-Y input selectionData communications Controlling Battery installation in the RCU Hardware set up of the projector address How to use your RCUUsing your RCU How to display a projector address? Input selection General Access Menu Items Source Pause key Analog Picture Controls Adjustment mode Start UP of the Adjustment Mode Start Up of the Adjustment Mode Random Access Adjustment Mode Starting up the random access adjustment modeOverview ‘Random Access Adjustment’ mode Internal Cross Hatch Pattern Selecting Setup Pattern Color Balance Random access adjustment mode selection menuPicture Tuning Sync Fast/Slow Adjustment Display the projected image in that specific color PeakingColor Select Press Enter to display the color select menu Focusing Focusing Geometry Geometry AdjustmentsHorizontal Phase Adjustment Phase Raster Shift Adjustment Left Right E-W Left-Right east-west Adjustments Left Side Correction Left Keystone Left BOW Left Side Correction TOP Bottom N-S Top-Bottom north-south Adjustments Size Adjustment Vertical Linearity AdjustmentLinearity Blanking TOP Bottom Left Right Blanking Adjustments Convergence Adjustment Coarse Convergence AdjustmentsConvergence Vertical corners Fine Convergence Adjustments Service Mode Starting up the Service modeOverview flowchart ‘Service’ mode Copy a Block IdentificationCopy a block Identification Delete ALL Blocks Deletion of blocksDeleting block by block Delete a Block Change password Change LanguageTotal Run Time Undo R & B convergence mid All settings to midpositionUndo all settings to midpos Convergence mid Arrow key Axial Astigmatism correction Dynamic Astigmatism spot shape adjustment CRT RUN in Cycle Projector Warm UP G2 AdjustmentCommon Settings 12C Diagnostics CRT run in cycle Projector Warm UP Projector warm up Source MESSAGES, WARNINGS, and Failures Failure DTV-992 Ultra DTV-992 RS 232 Control Appendix Sending a Record single instruction STX Decimal values $02,$00,$00,$51,$0A,$00,$00,$00,$01,$5C Sharpness Overview Quick Guide to using the EYE-QTMsystem Preparing your EYE-QTM Easy-to-use, high precision automatic convergence systemEasy-to-use, high precision automatic geometry system Compact, built-in system EYE-QTMMENU Access to EYE-QTMON-SCREEN Menus Setting the Configuration EYE-QTMSETUP Focusing the Camera Lens Centering the Camera Horizontally Centering the Camera TOUCH-UP on Source ON/OFF Centering the Camera Vertically TOUCH-UP on Timer Adjusting Other SourcesReference Source Learning a Reference What is Being Measured by EYE-QTM On Current Source Adjusting Screen Size TOUCH-UP Align on Current SourceAlign from Midposition on Current Source On ALL Sources TOUCH-UP on ALL SourcesAlign on ALL Sources Error Messages Align from Midposition on ALL SourcesInterrupting the Automatic Convergence Process No Pattern Error Status Reporting Forced BreakStatus Forced break EYE-QTMDIAGNOSTICS APX-16 Page RUMA-003700 rev