Failure | Runco dtv-992/992 ultra instruction

Messages, Warnings, and Failures

WARNING:

invalid

frequency input

WARNING:

default

settings loaded in the

E2PROM

table is deleted

The entered frequency or applied frequency of the source is out of the projector's range.

Adjustment settings are lost. Re load using Projector Control Soft ware via PC or MAC (if this option is available), or readjust image.

Message to inform that selected table is deleted. This message will be followed by `confirm message?,on which the user has to answer.

FAILURE

RWI communication

error

FAILURE EYE-Q communication

error

WAIT

starting up EYE-Q

Hardware failure. Call a qualified service technician.

Communication error between EYE-Q and the projector.

Call a qualified service technician.

Message during the start up of the EYE-Q. Message will disappear when the EYE-Q is ready to accept commands.

FAILURE

invalid RWI soft

version

FAILURE 12C error

addr. : 7FH3

FAILURE

short

circuit on 12C bus

Wrong software version in your projector. Call for technical sup port.

Hardware failure. Call a qualified service technician for repair.

Hardware failure. Call a qualified service technician for repair.

8-2

Image 46

Runco dtv-992/992 ultra, runco super hdtv dtv video projector manual Failure

Contents

DTV-992/992 Ultra Page Table of Contents Table of Contents APX-6 APP-3 EYE-QTMDIAGNOSTICS Safety Instructions Installation Instructions Safety Instructions Rear Panel Terminology Location and Function of ControlsFront Panel Terminology Local Keypad Control panel terminologyRCU control panel terminology IR Transmission Indicator Switching On/Off AC Power mains Cord ConnectionPower Check Connections Start up with full white image Signal Input Connection to the ProjectorPort No Projector Input Press Digit Button Rgbs or RGsB input selection Connecting a RGB Analog source with composite syncConnecting a RGB Analog source with Tri-level sync RGB3S or RG3sB input selection Connecting a Component source with Tri-level sync Connecting a Component sourceYYB-YS or R-YYsB-Y input selection YYB-Y3S or R-YY3sB-Y input selection Remote controlData communications Battery installation in the RCU Controlling How to display a projector address? How to use your RCUUsing your RCU Hardware set up of the projector address General Access Menu Items Source Input selection Analog Picture Controls Pause key Start UP of the Adjustment Mode Adjustment mode Start Up of the Adjustment Mode Starting up the random access adjustment mode Random Access Adjustment ModeOverview ‘Random Access Adjustment’ mode Selecting Setup Pattern Internal Cross Hatch Pattern Sync Fast/Slow Adjustment Random access adjustment mode selection menuPicture Tuning Color Balance Press Enter to display the color select menu PeakingColor Select Display the projected image in that specific color Focusing Focusing Phase Geometry AdjustmentsHorizontal Phase Adjustment Geometry Raster Shift Adjustment Left-Right east-west Adjustments Left Right E-W Left Side Correction Left Side Correction Left Keystone Left BOW Top-Bottom north-south Adjustments TOP Bottom N-S Vertical Linearity Adjustment Size AdjustmentLinearity Blanking Adjustments Blanking TOP Bottom Left Right Coarse Convergence Adjustments Convergence AdjustmentConvergence Fine Convergence Adjustments Vertical corners Starting up the Service mode Service ModeOverview flowchart ‘Service’ mode Identification IdentificationCopy a block Copy a Block Delete a Block Deletion of blocksDeleting block by block Delete ALL Blocks Change Language Change passwordTotal Run Time Convergence mid All settings to midpositionUndo all settings to midpos Undo R & B convergence mid Dynamic Astigmatism spot shape adjustment Arrow key Axial Astigmatism correction CRT run in cycle G2 AdjustmentCommon Settings 12C Diagnostics CRT RUN in Cycle Projector Warm UP Projector warm up Projector Warm UP MESSAGES, WARNINGS, and Failures Source Failure DTV-992 DTV-992 Ultra Appendix RS 232 Control Sending a Record single instruction Decimal values STX Sharpness $02,$00,$00,$51,$0A,$00,$00,$00,$01,$5C Quick Guide to using the EYE-QTMsystem Overview Compact, built-in system Easy-to-use, high precision automatic convergence systemEasy-to-use, high precision automatic geometry system Preparing your EYE-QTM Access to EYE-QTMON-SCREEN Menus EYE-QTMMENU EYE-QTMSETUP Setting the Configuration Focusing the Camera Lens Centering the Camera Centering the Camera Horizontally Centering the Camera Vertically TOUCH-UP on Source ON/OFF Adjusting Other Sources TOUCH-UP on TimerReference Source What is Being Measured by EYE-QTM Learning a Reference Adjusting Screen Size On Current Source Align on Current Source TOUCH-UPAlign from Midposition on Current Source TOUCH-UP on ALL Sources On ALL SourcesAlign on ALL Sources Align from Midposition on ALL Sources Error MessagesInterrupting the Automatic Convergence Process Status Reporting Forced Break No Pattern ErrorStatus Forced break EYE-QTMDIAGNOSTICS APX-16 Page RUMA-003700 rev