Decimal values, Stx | Runco dtv-992/992 ultra manual

APPENDIX 1

Example string to send to the projector with address 3 to turn it on/off

In decimal values

	STX		Offest		ADRe			CMDe		DATle			DAT2e DAT3e DAT4e CHKSe

	2		4			7			18		4			4		4		4		21

Always 2

Wake up projo

You choose offset. This is added to the rest of the bytes so that none of them equal 2 which would make the projector think its being told to wake up again. Normally

this is 0. It is set to 4 in this working example to show how it affects the value of the rest

of the bytes.

Optional data bytes plus offset. No data needs to be sent to turn on projector therefore these are equal to zero and offset is then added.

Add bytes from ADR to DAT4, keep 2 right most digits, then add offset. (3+14+0+0+0+0)+4=CHKSe

Command plus offset. (14+4)

Address of projector plus offset.

COMMAND CODE LIST

Transmitting the following codes is the same as using the keys of the IR remote.

	ENTER	07h	(7)	Enter button	CUR_UP	21h	(33)	Cursor up
	EXIT	08h	(8)	Exit button	CUR_DN	22h	(34)	Cursor down
	ADJUST	09h	(9)	Adjust button	CUR_RI	23h	(35)	Cursor right
	TEXT	0Dh	(13)	Menus On/Off	CUR_LE	24h	(36)	Cursor left
	STDBY	0Eh	(14)	Power On/Off	CON_UP	28h	(37)	Contrast +
	*NUM_0	10h	(16)		CON_DN	29h	(38)	Contrast -
	NUM_1	11h	(17)		BRI_UP	2Ah	(42)	Brightness +
	NUM_2	12h	(18)		BRI_DN	2Bh	(43)	Brightness -
	NUM_3	13h	(19)		SAT_UP	2Ch	(44)	Color +
	NUM_4	14h	(20)	Numeric	SAT_DN	2Dh	(45)	Color -
	NUM_5	15h	(21)	Numeric	HUE_UP	2Eh	(46)	Tint +
	NUM_5	15h	(21)	Keypad	HUE_UP	2Eh	(46)	Tint +
	NUM_6	16h	(22)	Keypad	HUE_DN	2Fh	(47)	Tint -
	NUM_6	16h	(22)		HUE_DN	2Fh	(47)	Tint -
	NUM_7	17h	(23)		SHA_UP	36h	(54)	Sharpness +
	NUM_8	18h	(24)		SHA_DN	37h	(55)	Sharpness -
	NUM_9	19h	(25)

The STDBY is a toggle for power ON/Off. If discreet
*Power On of Power Off commands are necessary please	*
see the chart of example strings.	Decimal Value in ( ).
see the chart of example strings.

APP-3

Image 50

Runco dtv-992/992 ultra, runco super hdtv dtv video projector manual Decimal values, Stx

Contents

DTV-992/992 Ultra Page Table of Contents Table of Contents APX-6 APP-3 EYE-QTMDIAGNOSTICS Safety Instructions Installation Instructions Safety Instructions Front Panel Terminology Location and Function of ControlsRear Panel Terminology RCU control panel terminology Control panel terminologyLocal Keypad IR Transmission Indicator Switching On/Off AC Power mains Cord ConnectionPower Check Connections Port No Projector Input Press Digit Button Signal Input Connection to the ProjectorStart up with full white image Rgbs or RGsB input selection Connecting a RGB Analog source with composite syncConnecting a RGB Analog source with Tri-level sync RGB3S or RG3sB input selection YYB-YS or R-YYsB-Y input selection Connecting a Component sourceConnecting a Component source with Tri-level sync Data communications Remote controlYYB-Y3S or R-YY3sB-Y input selection Battery installation in the RCU Controlling How to display a projector address? How to use your RCUUsing your RCU Hardware set up of the projector address General Access Menu Items Source Input selection Analog Picture Controls Pause key Start UP of the Adjustment Mode Adjustment mode Start Up of the Adjustment Mode Overview ‘Random Access Adjustment’ mode Random Access Adjustment ModeStarting up the random access adjustment mode Selecting Setup Pattern Internal Cross Hatch Pattern Sync Fast/Slow Adjustment Random access adjustment mode selection menuPicture Tuning Color Balance Press Enter to display the color select menu PeakingColor Select Display the projected image in that specific color Focusing Focusing Phase Geometry AdjustmentsHorizontal Phase Adjustment Geometry Raster Shift Adjustment Left-Right east-west Adjustments Left Right E-W Left Side Correction Left Side Correction Left Keystone Left BOW Top-Bottom north-south Adjustments TOP Bottom N-S Linearity Size AdjustmentVertical Linearity Adjustment Blanking Adjustments Blanking TOP Bottom Left Right Convergence Convergence AdjustmentCoarse Convergence Adjustments Fine Convergence Adjustments Vertical corners Overview flowchart ‘Service’ mode Service ModeStarting up the Service mode Identification IdentificationCopy a block Copy a Block Delete a Block Deletion of blocksDeleting block by block Delete ALL Blocks Total Run Time Change passwordChange Language Convergence mid All settings to midpositionUndo all settings to midpos Undo R & B convergence mid Dynamic Astigmatism spot shape adjustment Arrow key Axial Astigmatism correction CRT run in cycle G2 AdjustmentCommon Settings 12C Diagnostics CRT RUN in Cycle Projector Warm UP Projector warm up Projector Warm UP MESSAGES, WARNINGS, and Failures Source Failure DTV-992 DTV-992 Ultra Appendix RS 232 Control Sending a Record single instruction Decimal values STX Sharpness $02,$00,$00,$51,$0A,$00,$00,$00,$01,$5C Quick Guide to using the EYE-QTMsystem Overview Compact, built-in system Easy-to-use, high precision automatic convergence systemEasy-to-use, high precision automatic geometry system Preparing your EYE-QTM Access to EYE-QTMON-SCREEN Menus EYE-QTMMENU EYE-QTMSETUP Setting the Configuration Focusing the Camera Lens Centering the Camera Centering the Camera Horizontally Centering the Camera Vertically TOUCH-UP on Source ON/OFF Reference Source TOUCH-UP on TimerAdjusting Other Sources What is Being Measured by EYE-QTM Learning a Reference Adjusting Screen Size On Current Source Align from Midposition on Current Source TOUCH-UPAlign on Current Source Align on ALL Sources On ALL SourcesTOUCH-UP on ALL Sources Interrupting the Automatic Convergence Process Error MessagesAlign from Midposition on ALL Sources Status Forced break No Pattern ErrorStatus Reporting Forced Break EYE-QTMDIAGNOSTICS APX-16 Page RUMA-003700 rev