Interface Board Replacement | SATO LM408/412E specs

Unit 6: Maintenance

INTERFACE BOARD REPLACEMENT

Circuit boards generally have long lives due to the lack of moving parts. Generally, if a circuit board becomes defective, it is contributable to a negative external condition.

If it is determined that the circuit board has become defective, search the printer over for possible visual factors that may have led to the damage.

1.Switch off the printer and disconnect power supply cord.

2.Disconnect interface cable (1, Figure 6-2) from defective interface board (2).

3.Remove two screws (3) securing defective interface board (2) to printer (4).

4.Insert replacement interface board (2) into printer (4) and secure using two screws (3).

5.Connect interface cable (1).

Figure 6-2, Interface Board Replacement

LM408-412e Operator Manual

6-5

PN: 9001155A

Image 73

SATO LM408/412E manual Interface Board Replacement

Contents

Printer Sato America, Inc Table of Contents Troubleshooting Printer Configuration Appendix MaintenanceOffset Introduction Equipment Damage About this Manual 1a, Primary Components General Descript Operator Panel Features LED Definition Control FeaturesDipswitches Definition Operator Panel Technical Data Power Physical CharacteristicsEnvironmental Processing Sensing CommandMedia Ribbon Character Font Capabilities UPC A/E Barcode CapabiltiesMSI Postnet Installation Unpacking & Parts Identification Unpacking & Parts Identification Site Location Printer InstallationCable Connection Media & Ribbon Loading Media Selection 3b, Fan-fold Media Loading TEAR-OFF Mode Operational Mode SelectionContinuous Mode Accessories Installation unit for guidance Interface SpecificationsInterface Selection RS232C HIGH-SPEED Serial Interface OFF ODD Even None PIN Direction Signal DefinitionOFF ON/X-OFF Host Direction READY/BUSY Cable Requirements DB9Printer ON/X-OFF Cable Requirements PIN Assignments Signal Direction SpecificationsIEEE1284 Parallel Interface ACK Setting Dipswitch SettingsUniversal Serial BUS USB Local Area Network LAN Ethernet Software Specifications 802.11G Wireless Interface LED Indicator Status Description Switch Setting ALL Interfaces Interface SignalsCable Requirements 50 of 500 items in the history buffer Receive Buffer Control Interface Installation Accessories Installation Printer Configuration Unit 4 Printer Configuration Dipswitch Functions Switch Setting Description Dipswitch Settings Normal Mode Configuration Modes Advanced Mode Advanced Mode No change User Download Mode ACK Signal XX.X Service Mode Card Mode Card Mode Motion Mode Move Mode History Control Mode History Control Mode DSW7 on Line + Feed + Power Protocol Initialization Mode Counters Mode Counters Mode 10, Test Print Mode Test Print Mode 11, Boot Download Mode Boot Download Mode 12, Flash Memory Download Mode Flash Memory Download Mode Yes Default Setting Mode DSW4 on Power HEX Dump Mode 15, Maintenance Mode Maintenance Mode Menu Definition Tables Normal Mode TableMenu Description Advanced Mode Table Language options Transitional menu screen to access the Service ModeVoltageThreshold low voltage + high voltage = 12 volts Service Mode Table Operator to the biginning of the Card Mode Is only a transitional menu screen for the Service ModeIs only a transitional menu screen to access the Move Mode Transitional menu screen to access the Move Mode Without pause for application Determined Continuous or Tear-OffHas been removed for application Transitional menu screen to access the Counters Mode Counters Mode Table Configuration The printer’s configuration settings Is the initial screen of the Test Print ModeBarcode The printer’s installed barcodes Font The contents of the installed fonts To proceed to the Factory Mode Maintenance Mode Table Troubleshooting Error Signal Troubleshooting Troubleshooting Table Printer Creates a Blank Label No Printed ImageIncorrect Label Positioning Smeared Print Images CHK Troubleshooting Step Interface Troubleshooting LAN Ethernet Interface DSW4 on Power Test Print Troubleshooting Feed Test Label Printing Sample Test Label Maintenance PRINTER, Excersize Care to Prevent Print Head Damage Cleaning Procedures Print Head Replacement Replacement Procedures 1a, Print Head Replacement Interface Board Replacement Interface Board Replacement Fuse Replacement Fuse Replacement Print Head Balance Adjustment Adjustment Procedures 5a, Print Head Alignment Print Head Alignment Head Balance and Print Head Alignment Ribbon Guide Alignment Label Sensor Positioning Label Sensor Positioning Ribbon Spindle Tensioning Ribbon Spindle Tensioning Potentiometer DESCRIPTION/PROCEDURE Operational AdjustmentsDarkness Label Print Direction Appendix Print Setup Dimensions Print Setup Dimensions Reflective Sensor Label Reference Position 3a, Standard Position Label Adjustment Diagram Printer Connection Diagram 5a, Printer Loading Diagram Printer Loading Diagram 5c, Printer Loading Diagram Glossary GlossaryAscii Being its mating half Bytes Collection of 8 bits used in the binary systemIs a plug male and the other is a socket female Half. The core is convexed and the cavity is concaved Dram DPIEeprom Data transmission, seven additional bits are required Tag would typically have to be removed from its object PowerNext label for printing To attach two or more objects LED LCD Or voltage divider Primary Potentiometer RF/AIS RAMRF/DC Rfid RPM ROMSAM Sbpl Sram Glossary