Manuals / SATO / Computer Equipment / Printer

SATO LM408/412E manual Accessories Installation, Interface Installation

Models: LM408/412E

1 98

Download 98 pages 19.33 Kb

Page 31

Image 31

Unit 3: Installation

ACCESSORIES INSTALLATION

This chapter covers printer accessory installation procedures that are operator allowed.

INTERFACE INSTALLATION

The diagram below displays the physical installation of interface hardware. Refer to the Configuration unit of this manual for instructions on printer setup for the interface type chosen.

1.Switch off the printer and disconnect power supply cord.

2.Route interface cable (1, Figure 3-7) from host computer to interface board (2).

3.Insert interface board (2) into printer (4) and secure using two screws (3).

4.Connect interface cable (1).

Figure 3-7, Interface Installation

LM408-412e Operator Manual

3-16

PN: 9001155A

Page 31

Image 31

SATO LM408/412E manual Accessories Installation, Interface Installation

Contents

OPERATOR MANUAL LM408/412e PRINTERE-Mail satosales@satoamerica.com techsupport@satoamerica.com SATO America, Inc10350A Nations Ford Road Charlotte, NC Main Phone 704 Technical Support Hotline 704 Technical Support Fax 704TABLE OF CONTENTS TECHNICAL DATAINSTALLATION INTRODUCTIONTROUBLESHOOTING PRINTER CONFIGURATIONAPPENDIX MAINTENANCEINTRODUCTION About This Manual General Description Control FeaturesWARNING PROVIDES INFORMATION THAT, IF UNHEEDED, MAY RESULT IN ABOUT THIS MANUALPERSONAL INJURY Ribbon Supply Sprindle GENERAL DESCRIPTPrint Assembly Ribbon Rewind SpindleKEYS CONTROL FEATURESPOTENTIOMETERS LCD Display LED Display Function Keys Potentiometers Dipswitch ComplexFigure 1-2, Operator Panel Unit 1 IntroductionRegulatory Approvals Character Font Capabilities Barcode Capabilities TECHNICAL DATAPhysical Characteristics Power Enviromental Processing Interface Modules Print Sensing Media Ribbon CommandPROCESSING PHYSICAL CHARACTERISTICSPOWER ENVIRONMENTALRIBBON COMMANDSENSING MEDIAVECTOR FONT CHARACTER FONT CAPABILITIESMATRIX FONTS AUTO SMOOTHING FONTSBARCODE CAPABILTIES Accessories Installation INSTALLATIONUnpacking & Parts Identification Printer Installation Operational Mode Selection Interface SelectionUNPACKING & PARTS IDENTIFICATION SITE LOCATION PRINTER INSTALLATIONCABLE CONNECTION MEDIA & RIBBON LOADING MEDIA SELECTIONFigure 3-3a, Rolled Media Loading Figure 3-3b, Fan-fold Media Loading Unit 3 InstallationFigure 3-3c, Ribbon Loading CONTINUOUS MODE OPERATIONAL MODE SELECTIONTEAR-OFF MODE CONTINUOUS MODERS232C HIGH-SPEED SERIAL INTERFACE INTERFACE SELECTIONDIRECTION SIGNAL DEFINITIONDIPSWITCH SETTINGS READY/BUSY INTERFACE SIGNALSFigure 3-5, Serial Connector Pin Assignments Figure 3-6, Parallel Connector Pin Assignments IEEE1284 PARALLEL INTERFACE3-10 LOCAL AREA NETWORK LAN ETHERNET UNIVERSAL SERIAL BUS USBSWITCH 802.11G WIRELESS INTERFACE LED INDICATOR STATUS DIPSWITCH SETTINGSSWITCH SETTINGALL INTERFACES RECEIVE BUFFER CONTROL INTERFACE INSTALLATION ACCESSORIES INSTALLATIONPrinter Configuration Dipswitch Setting Configuration Modes PRINTER CONFIGURATIONMenu Definition Tables Unit 4 Printer Configuration PRINTER CONFIGURATIONDIPSWITCH SETTINGS NORMAL MODE CONFIGURATION MODESFigure 4-2, Advanced Mode ADVANCED MODEFigure 4-3, User Download Mode USER DOWNLOAD MODEFigure 4-4, Service Mode SERVICE MODEFigure 4-5, Card Mode CARD MODEFigure 4-6, Motion Mode MOVE MODEFigure 4-7, History Control Mode HISTORY CONTROL MODE4-10 Figure 4-8, Protocol Initialization Mode PROTOCOL INITIALIZATION MODE4-11 Figure 4-9, Counters Mode COUNTERS MODE4-12 Figure 4-10, Test Print Mode TEST PRINT MODE4-13 Figure 4-11, Boot Download Mode BOOT DOWNLOAD MODE4-14 Figure 4-12, Flash Memory Download Mode FLASH MEMORY DOWNLOAD MODE4-15 Figure 4-13, Default Setting Mode DEFAULT SETTING MODE4-16 Figure 4-14a, Hex Dump Mode HEX DUMP MODE4-17 Figure 4-15, Maintenance Mode MAINTENANCE MODE4-18 MENU DEFINITION TABLES point respectively DESCRIPTION USER DOWNLOAD MODE TABLESERVICE MODE TABLE Unit 4 Printer Configuration255mm other than the default setting DESCRIPTION CARD MODE TABLEMOVE MODE TABLE DESCRIPTIONMENU MOVE MODE TABLEHISTORY CONTROL MODE TABLE PROTOCOL INITIALIZATION MODE TABLEDESCRIPTION COUNTERS MODE TABLEMENU MENU TEST PRINT MODE TABLEBOOT DOWNLOAD MODE TABLE Is the initial screen of the Test Print ModeMAINTENANCE MODE TABLE FLASH DOWNLOAD MODE TABLEDEFAULT SETTING MODE TABLE HEX DUMP MODE TABLEClear MENUError Signal Troubleshooting Troubleshooting Table TROUBLESHOOTINGInterface Troubleshooting Test Print Modes Machine ERROR SIGNAL TROUBLESHOOTINGERROR DISPLAYS Sensor ErrorTROUBLESHOOTING TABLE TROUBLESHOOTING TABLESMEARED PRINT IMAGES NO PRINTED IMAGEPRINTER CREATES A BLANK LABEL INCORRECT LABEL POSITIONINGUNIVERSAL SERIAL BUS USB INTERFACE INTERFACE TROUBLESHOOTINGPARALLEL INTERFACE RS232 SERIAL INTERFACETROUBLESHOOTING STEP 802.11G WIRELESS INTERFACELAN ETHERNET INTERFACE CENTRONICS INTERFACEHEX DUMP MODE TEST PRINT TROUBLESHOOTINGDSW4 ON POWER Configuration TEST LABEL PRINTINGUnit 5 Troubleshooting FEED + POWERD S W Label Contents Will Vary Depending on Test Label TypeUnit 5 Troubleshooting SAMPLE TEST LABELCleaning Procedures Replacement Procedures Adjustment Procedures MAINTENANCEWHEN CLEANING TO PREVENT PERSONAL INJURY CLEANING PROCEDURESWARNING DISCONNECT POWER SUPPLY TO THE PRINTER AND ALLOW TO COOL TO ROOM TEMPERATURE PRIOR TO CLEANING. EXCERSIZE CAREPRINT HEAD REPLACEMENT REPLACEMENT PROCEDURESFigure 6-1b, Print Head Replacement Figure 6-1a, Print Head ReplacementUnit 6 Maintenance Figure 6-2, Interface Board Replacement INTERFACE BOARD REPLACEMENTFigure 6-3, Fuse Replacement FUSE REPLACEMENTPRINT HEAD BALANCE ADJUSTMENT ADJUSTMENT PROCEDURESFigure 6-5a, Print Head Alignment PRINT HEAD ALIGNMENTFigure 6-5b, Print Head Alignment Figure 6-6, Ribbon Guide Alignment RIBBON GUIDE ALIGNMENTFigure 6-7, Label Sensor Positioning LABEL SENSOR POSITIONING6-10 Figure 6-8, Ribbon Spindle Tensioning RIBBON SPINDLE TENSIONING6-11 DESCRIPTION/PROCEDURE OPERATIONAL ADJUSTMENTSPOTENTIOMETER LABEL PRINT DIRECTION CONTINUOUS MODETEAR-OFF MODE Unit 6 MaintenanceLabel Adjustment Diagram Printer Connection Diagram Glossary Print Setup Dimensions Label Reference Position DiagramAPPENDIX Mark, Gap, Paper-End PRINT SETUP DIMENSIONSGap 0.67 Eye-Mark 0.24LABEL PRINT DIRECTION CONTINUOUS MODETEAR-OFF MODE LABEL REFERENCE POSITIONUnit 7 Appendix LABEL ADJUSTMENT DIAGRAMFigure 7-3a, Standard Position Figure 7-3b, Tear-Off PositionHost Computer PRINTER CONNECTION DIAGRAMPower Cord Power Receptacle Unit 7 AppendixUnit 7 Appendix PRINTER LOADING DIAGRAMFigure 7-5a, Printer Loading Diagram Figure 7-5b, Printer Loading DiagramUnit 7 Appendix Figure 7-5c, Printer Loading DiagramGLOSSARY GLOSSARYGLOSSARY Diode Factory Programming predetermined activity GLOSSARY GLOSSARY GLOSSARY GLOSSARY Troubleshoot