Connecting a PC to the central unit | Sennheiser SDC 8000 specs

Setting up the SDC 8000 system

Connecting a PC to the central unit

If your system comprises interpreter consoles, you require a PC with two serial interfaces:

y The	conference	management	software	accesses	the	conference
configuration via the central unit’s COM 3 interface .
y The	interpreter	management	software	accesses	the	interpreter
configuration via the central unit’s COM 1 interface .

To connect a PC to the central unit:

Connect one serial interface of the PC to the COM 3 interface of the central unit.

Connect the other serial interface of the PC to the COM 1 interface	of
the central unit.

Note!

If you are using more than one central unit, the PC has to be connected to the “master” central unit.

For connecting a PC to the central unit, you require the cables shown below:

5 m

PC SUB-D F

PC SUB-D F

Pin 1: Not connected	Pin 1: Not connected
Pin 2: RX Receive	Pin 2: RX Receive
Pin 3: TX Transmit	Pin 3: TX Transmit
Pin 4: Not connected	Pin 4: DTR Data Terminal Ready
Pin 5: GND	Pin 5: GND
Pin 6: Not connected	Pin 6: DSR Data Set Ready
Pin 7: Not connected	Pin 7: RTS Request to Send
Pin 8: Not connected	Pin 8: CTS Clear to send
Pin 9: Not connected	Pin 9: Not connected

53

Image 53

Sennheiser SDC 8000 system manual Connecting a PC to the central unit

Contents

SDC Thank you for choosing Sennheiser Contents Via a PA system Configuring the interpretation system 100 Appendix a Safety information SDC 8000 the digital conference and interpretation system Conference consoles Overview of the components SDC 8000 system $!# Technology used Consoles All consoles featureComponents of the SDC 8000 system in detail Interpreter console features SDC 8000 D conference unit SDC 8000 C chairman unit SDC 8000 DC conference unit SDC 8000 CC chairman unit Vote LED SDC 8000 DV conference unit SDC 8000 CV chairman unit Autofloor LED SDC 8000 ID interpreter console SDC 8000 CU central unit SDC 8000 AO analog output unit optional System cables Operating the components SDC 8000 system Direct Access modeOperating the delegate units Taking the floor / Making a request to speak Operating the components of the SDC 8000 system On your console go off Turning off the microphone / Cancelling a request to speak With request modeWith Req. No clear mode Voting Selecting an interpretation channel Operating the VIP units Using the chip card slot of a conference consoleOperating the chairman unit Turning all active conference consoles off priority Assigning a participant the speaking right Starting a voting session Request Operating the interpreter consoles Configuring the B-channel of an interpreter console Using the interpreter console Adjusting the volume of the consoles’ built-in loudspeakers Switching between the A-channel and the B-channelOperating the central unit Muting the microphone of the interpreter console Operating control Menu level F1, F2 and F3 menu keysMenu operating controls Working with the central unit’s operating menu Connecting cable strings to a central unit Interconnecting the conference/interpreter consolesInterconnecting up to 10 central units Structuring the SDC 8000 system Expansion stage 2 one central unit with up to 90 consoles Expansion stage 1 one central unit with up to 15 consoles Determining maximum cable lengths Calculating the voltage drop on the system cables Structuring an interpretation system Mode between booths Mixed Selectable modes between or within interpreter boothsMode between booths Override Mode between booths Toggle Override Mode in booths Override Mode in booths MixedAuto-floor function Example AUTO-FLOOR Connecting external audio sources Using external equipment Structuring the SDC 8000 system Preparing the SDC 8000 system components for set up Setting up the SDC 8000 system Interconnecting the consoles Interconnecting the SDC 8000 system componentsConnecting a cable string to the central unit Interconnecting several central units Turning the central units on and off Connecting additional equipment Carrying out remote conferences Pin assignment of the 9-pole sub-D socket AUX OUT Connecting PA systems, recording units, etc Daisy-chaining SDC 8000 AO analog output units Connecting a PC to the central unit Introduction to the central unit’s operating menu Configuring the SDC 8000 systemStart display Six main menus Enter Exit Submenus of the Conference menu part 1 Submenus of the Conference menu part 2 Submenus of the Conference menu part 3 Submenus of the Conference menu part 4 Submenus of the Conference menu part 5 Submenus of the Conference menu part 6 Submenus of the Interpretation menu part 1 Submenus of the Interpretation menu part 2 Submenus of the Interpretation menu part 3 Submenus of the Interpretation menu part 4 Submenus of the Interpretation menu part 5 Enter Submenus of the Aux-In/Out menu part 1 Submenus of the Aux-In/Out menu part 2 Submenus of the Aux-In/Out menu part 3 Submenus of the Aux-In/Out menu part 4 Submenus of the Aux-In/Out menu part 5 Submenus of the Aux-In/Out menu part 6 Submenus of the System menu part 1 Submenus of the System menu part 2 Submenus of the Language and the License menu part 1 Configuring the conference system Settingthe volume of theconsoles’ built-inloudspeakersTurning on the central unit for the first time Automatically initializing all conference consoles Manually initializing all conference consoles Reserving a microphone number Selecting a conference mode Setting the speaker limit Resetting the conference system Adjusting the audio settings for the consoles’ microphones Testing the consoles’ microphones Testing the consoles’ built-in loudspeakers Working with the interpreter configuration Configuring the interpretation systemConfiguring the display of the voting options Creating a new interpreter configuration Loading a previously saved interpreter configuration Modifying the currently active interpreter configuration Options Setting the max. number of interpreter booths/languagesSetting the max. number of interpreter consoles per booth Configuring the operating mode within a booth Configuring the operating mode between booths Configuring the second target language B-channel of a booth Configuring the language options for the interpreter boothsConfiguring the main target language A-channel of a booth Enabling the auto-relay interpretation function Auto-floor ENG To transmit the selected booth number to Adding interpreter consoles to an existing configuration Resetting the interpretation system Choosing the audio inputs and outputs Configuring the audio inputs and outputsAdjusting the volume of the audio outputs Turning the audio inputs or outputs on and off Configuring the audio outputs for remote conferencingAssigning a channel to an audio output Configuring the outputs of the SDC 8000 analog output unit Adjusting the input level of an audio inputAdjusting the input sensitivity of an audio input OUT Making a system diagnosis Configuring connected additional componentsChecking the communication within a cable string Camera control Configuring an ambient sound console Choosing the language of the central unit’s operating menu Software, language and license Displaying the central unit’s serial number Maintenance and care If problems occurReplacing a fuse Conference/interpreter console does not work Accessories SDC 8000 C SpecificationsSDC 8000 D SDC 8000 CC SDC 8000 DC SDC 8000 CV SDC 8000 DV SDC 8000 ID 108 RJ 45 cable SDC 8000 AO analog output unit Appendix a Camera control protocol Syntax of the commands Notation of the general syntax Commands Appendix B Control panel protocol Commands 113 114 Appendix C Repeater for the SDC 8000 system Approval 115